trinityboringsolutions.com

Utility Core Drilling in Oklahoma City

Trinity Boring Solutions core drills concrete driveways, parking lots, sidewalks and curbs in Oklahoma City to expose the gas, fiber, water, sewer and electric lines under them before a directional bore. A small core comes out of the concrete, a high pressure water wand or hydrovac daylighting exposes the line, and then we have our depths.

Since 1965 Family Business Licensed, Insured and Bondable 24/7 On Call Core, Daylight, Then Bore OKC Metro and Statewide

Utility core drilling in Oklahoma City, answered in one paragraph. Utility core drilling is cutting a small round hole through concrete with a hollow diamond bit so the buried line under it can be exposed and its depth measured before a directional bore. Trinity Boring Solutions, a family business since 1965 and a directional boring contractor based at 9102 NW Expressway in the Oklahoma City metro, cores driveways, parking lots, sidewalks and curbs on the locate marks, then exposes each gas, fiber, water, sewer or electric line with a high pressure water wand or hydrovac daylighting. On a bank job at the Mortgage Spot on NW Expressway, we spotted a gas line and an AT&T fiber line at our core holes before the bore. We core drill in Edmond, Oklahoma City, Moore and Norman and across Oklahoma. Call (405) 409-7423.

Utility core drilling at a glance

  • What it is. A hollow drill bit with diamond segments cuts a round plug, called a core, out of the concrete and leaves a clean round hole.
  • Why we do it. Okie811 marks show the approximate location of a line, 2 feet on either side of it, and they do not show depth. A core gets us down to the line without breaking out the slab.
  • How we expose the line. Through the core, a high pressure water wand or hydrovac daylighting opens the ground until the line is in sight.
  • What we get. Once the line is exposed, we have our depths, so we can plan the bore around every line we found.
  • Where we core. Concrete driveways, parking lots, sidewalks and curbs, and at the pole or the box where conduit has to come up.
  • Who does it. Trinity Boring Solutions, a family business since 1965. Licensed, insured and bondable, and on call 24/7.
Concrete core next to a fresh core hole on a bank driveway on NW Expressway in Oklahoma City, cut to expose a gas line and an AT&T fiber line
The core drill on a bank driveway at the Mortgage Spot on NW Expressway in Oklahoma City, where we spotted a gas line and an AT&T fiber line.

What Is Core Drilling in Concrete?

Core drilling is drilling a round hole through concrete with a hollow bit. Penhall describes diamond core drilling as a cutting method that uses a hollow, cylindrical bit with diamond segments to grind through hard material and pull out a solid cylindrical plug, known as a core. Penhall says the result is a clean, precise, perfectly round hole with smooth edges and no vibration damage to the concrete around it.

Penhall also notes that the most common use for core drilling is making openings for mechanical, electrical and plumbing work. Utility core drilling is the same cut made for a different reason. We core through a driveway or a parking lot right on the locate marks so we can get down to the line under the slab. The core comes out in one piece and leaves a small hole to work through.

Why We Core Drill Before a Directional Bore

Locate marks show about where a line is. They do not show how deep it is. Okie811 defines the approximate location of a buried line as a strip of land 2 feet on either side of it, and the Okie811 Excavator Guide says not to assume the depth of a line based on the markings. Okie811 also says it does not have depth information for underground lines.

A bore that crosses a gas line or a fiber line needs that depth, and under concrete there is no way to see the line until the concrete is open. Core drilling allows us to cut out small pieces of concrete so we can use a high pressure water wand or hydrovac daylighting to expose the line. Once we have exposed it, we have our depths, and then we can begin our directional boring.

That is also standard practice. Ditch Witch says the best practice is to always expose a utility that the bore path crosses, and the Okie811 guide lists soft digging and vacuum excavation among the ways to work near a marked line inside the tolerance zone. Our guide to locating underground utilities before boring covers the whole locate process.

Private lines are the other reason. The Okie811 Safe Digging Guide says secondary water, sewer, gas and electric lines are private lines and are not marked when you call 811, and that lines running from the right of way or the meter to a home or business count as private lines, so a private line locator has to find them. On a commercial lot, those lines can run under the same concrete the bore has to cross.

How Utility Core Drilling Works, Step by Step

  1. Call in the locate. Okie811 locate requests are free. The utilities paint their marks: yellow for gas, orange for communication lines like fiber, red for electric, blue for water and green for sewer.
  2. Pick the core spots. We set our cores on the locate marks where the bore path crosses each line.
  3. Core the concrete. The core drill cuts through the drive or parking lot, and the core comes out in one round piece.
  4. Expose the line. A high pressure water wand or hydrovac daylighting opens the ground under the core until the line is in sight.
  5. Get the depth. With the line exposed, we have its depth and its exact spot.
  6. Bore. With every crossing exposed, we begin the directional bore and stay clear of the lines we found.

See our page on 811 locates before boring in Oklahoma for the full locate rules.

Core Drilling Before a Bore at a Bank on NW Expressway

A bank at the Mortgage Spot on NW Expressway in Oklahoma City needed to put its electric underground under a driveway. We did a directional bore and installed 2 inch HDPE. We were able to cut concrete out, and we had to core drill across the parking lot.

At the core holes we spotted a gas line and an AT&T fiber line. Core drilling let us cut out small pieces of concrete so a high pressure water wand or hydrovac daylighting could expose them. Once they were exposed, we had our depths, and then we began our directional boring.

We had to go across sewer lateral lines, water lines, fiber optic lines and gas lines. We were able to stub this one up right where the customer wanted it, so they could put it into their box.

CustomerA bank at the Mortgage Spot on NW Expressway, Oklahoma City
The workPut the electric underground under a driveway
Core drillingAcross the parking lot
Spotted at the coresA gas line and an AT&T fiber line
Exposed withA high pressure water wand or hydrovac daylighting
The boreDirectional bore with 2 inch HDPE
Lines crossedSewer laterals, water lines, fiber optic lines and gas lines
ConcreteCut out at the pole
FinishStubbed up right where the customer wanted it, at their box
Ditch Witch locator over a small core hole at the curb before a directional bore under a driveway in northwest Oklahoma City
A Ditch Witch locator over a core hole at the curb.
Crew member running a high pressure water wand on a concrete drive beside yellow gas locate marks on NW Expressway in Oklahoma City
Running the high pressure water wand on the concrete drive, beside the yellow gas marks.
Concrete cut out at the base of an electric meter pole with a vac hose, ready for the conduit stub up on NW Expressway in Oklahoma City
Concrete cut out at the base of the pole.
Electric conduit stubbed up beside the customer box on the pole after a directional bore with 2 inch HDPE on NW Expressway in Oklahoma City
Stubbed up right where the customer wanted it, so they could put it into their box.

For more on boring electric for a business, see our underground electrical conduit installation and boring for electricians pages.

Where We Core Drill

Driveways

We core the drive on the marks so we know what is under it before the bore crosses it.

Parking Lots

On the bank job we cored across the parking lot and spotted a gas line and an AT&T fiber line before we bored.

Sidewalks and Curbs

A small core at the curb or in the walk gets us down to a marked line and leaves the rest of the concrete in place.

At the Pole or the Box

Where conduit has to come up, we cut the concrete out so the stub up lands right where the customer wants it.

Core Drilling, Potholing and Daylighting

These words get mixed up, so here is how we use them. Core drilling cuts through the concrete. Potholing and daylighting expose the line under it with water and vacuum. Vermeer says this work goes by several names, including potholing, daylighting and keyholing, and that the terms are often used interchangeably. Ditch Witch says exposing a utility with soft excavation is commonly called daylighting.

On a paved site, the core comes first and the daylighting comes second. Vermeer puts the reason plainly: potholing visually confirms the exact position and depth of the line, and that helps crews plan a bore path with confidence. Our hydrovac daylighting and utility potholing pages cover that step, and our guide to underground utility depths covers how deep lines are usually buried in Oklahoma.

Utility Core Drilling Service Area

We core drill in Edmond, Oklahoma City, Moore and Norman first, and across the rest of the metro, including Yukon, Mustang, Bethany, Warr Acres, Midwest City and Del City. We also core drill on our directional bore jobs across Oklahoma. Trinity Boring Solutions is based at 9102 NW Expressway, Yukon, OK 73099, and we are on call 24/7. If you are pricing a bore under a drive, our page on the cost to bore under a driveway walks through what changes the price.

Utility Core Drilling FAQ

What is utility core drilling?

Utility core drilling is cutting a small round hole through concrete over a buried line so the line can be exposed and its depth measured before a directional bore. Trinity Boring Solutions cores driveways, parking lots and sidewalks in Oklahoma City, then exposes the line with a high pressure water wand or hydrovac daylighting.

Why core drill a driveway or parking lot before boring?

Locate marks show the approximate location of a line, 2 feet on either side of it, and not its depth. Core drilling gets through the concrete so the line can be exposed. Once it is exposed, we have our depths and can begin the directional bore.

What is diamond core drilling?

Diamond core drilling uses a hollow round bit with diamond segments. The bit grinds through the concrete and pulls out a solid round plug called a core, which leaves a clean round hole.

Can you core drill a concrete slab or driveway?

Yes. We core drill concrete driveways, parking lots, sidewalks and curbs to reach the lines under them. On a bank job at the Mortgage Spot on NW Expressway in Oklahoma City, we core drilled across the parking lot and spotted a gas line and an AT&T fiber line.

How much does concrete core drilling cost?

It depends on the job: how many cores it needs, the concrete, and how many lines have to be exposed. Call (405) 409-7423 with the address and the work, and we will give you a quote.

Is there concrete core drilling near me in Oklahoma City?

Trinity Boring Solutions is based at 9102 NW Expressway in Yukon and core drills concrete in Edmond, Oklahoma City, Moore, Norman and across the metro. We are on call 24/7 at (405) 409-7423.

What is the difference between core drilling and potholing?

Core drilling cuts through the concrete. Potholing, also called daylighting, uses water and vacuum to expose the line under it. On a paved site we core first, then expose the line through the core.

Does Okie811 show how deep a line is?

No. Okie811 says not to assume the depth of a line from the markings, and it does not have depth information for underground lines. That is why we expose each line and get the depth before we bore.

What do the locate paint colors mean?

In Oklahoma, yellow is gas, oil or steam, orange is communication lines like fiber, red is electric, blue is drinking water, purple is reclaimed water and irrigation, green is sewer and drain, pink is temporary survey and white is the proposed excavation.

Will 811 mark private lines?

No. Okie811 says secondary water, sewer, gas and electric lines, like the lines from the meter to a home or business, are private lines and are not marked when you call 811. A private line locator has to find them.

Need Concrete Cored Before a Bore?

Call Trinity Boring Solutions. We core the concrete, expose the lines, get our depths and bore, in Edmond, Oklahoma City, Moore, Norman and across Oklahoma. Family business since 1965, licensed, insured and bondable.

Sources

Related Boring and Utility Services

Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com

Talk to the crew that does the work

Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.

Call (405) 409-7423

Answered by a person, not a call center.

Would rather not call? Send the details and we will come back with a written quote.

Quick Quote In Page