trinityboringsolutions.com

Damon Texas Directional Boring: Edna Soil, Texas State Highway 36 and Cow Creek

Quick Answer: Will the pavement stay intact if your line has to pass beneath Texas State Highway 36? Trinity Boring Solutions does directional boring, also called horizontal directional drilling (HDD), in Damon, Texas, for crossings like this. The Damon site is 494 road miles from our Yukon, Oklahoma main office, and Pipeline Road is one local route to consider for access. Edna soil maps to heavy clay below the surface. That sticky ground calls for careful fluid control and staged reaming.

Family Business Since 1965 Boring Since 1982 24 Hour Phone No Utility Strike in 25 Years

Damon bores at a glance

  • Unincorporated community in Brazoria County, Texas. Population 436 (2020 Census count).
  • Road distance from our Yukon, Oklahoma main office: 494 miles, about 9.8 hours of driving.
  • Ground: Edna soil is mapped on 73 percent of the area, with clay about 40 inches down.
  • Rock: no bedrock is mapped in the top 60 inches.
  • Highways inside the boundary: Texas State Highway 36. State permit office: TxDOT Houston District.
  • Railroad track inside the boundary: none mapped.
  • Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
  • Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
  • Phone answered 24 hours a day: (405) 409-7423

Does anyone do directional boring near Cow Creek in Damon?

Will your line pass beneath Texas State Highway 36 without cutting the pavement? We take directional boring work in Damon, in Brazoria County, where the 2020 Census counted 436 people. We install water, sewer, gas, electric conduit and fiber, including lines routed along Stockwell Street or Pipeline Road. The route and access points depend on the address and the line you need.

Our main office is in Yukon, Oklahoma, and Damon work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. We have done directional boring since 1982, after our family business began in 1965. Four decades of boring matter in Damon, where Edna soil gives way to heavy clay below the surface and requires attention to the drilling fluid and reaming plan.

Aerial view of a bore pit with drill rig and conduit alongside a directional drill rig and conduit on a concrete lot
Our crew at a bore pit beside the directional drill on a conduit job, seen from above. Photos on this page are from our jobs in Oklahoma and Texas.

How does Edna soil affect a bore in Damon?

The USDA soil survey maps Edna series across 73 percent of Damon and Bernard across 27 percent. Edna fine sandy loam, with 1 to 3 percent slopes, covers 68 percent of the mapped area; Bernard clay loam covers 21 percent. About 40 inches down, the survey maps clay throughout the area, with an average clay content of 44 percent. Fine sandy loam is the surface texture across 70 percent, while clay loam accounts for 27 percent. Our Edna and Bernard soil maps show mapped patterns, not test borings, so we verify conditions during planning. The deeper clay can cling to a reamer and grip a pipe.

USDA soil survey, inside the Damon mapped community boundaryWhat is mapped
Soil series mappedEdna 73 percent and Bernard 27 percent
Texture at the surfacefine sandy loam 70 percent, clay loam 27 percent and loam 3 percent
Texture about 40 inches downclay 100 percent
Engineering class about 40 inches downfat clay (CH) 100 percent
Average clay content about 40 inches down44 percent
Bedrock mapped within 60 inchesNone mapped
Seasonal water table within 60 inches100 percent of the area
Flood prone soils0 percent of the area
High corrosion risk for uncoated steel100 percent of the area

Bedrock is not mapped in the top five feet of Damon, but that does not rule out rock deeper down. The USDA soil survey maps a seasonal water table within 60 inches throughout the area, so pits along Pipeline Road may need pumping. Near Cow Creek, we do not have mapped flood prone soils to use as a substitute for site specific review. High steel corrosion risk covers the mapped area, so the line owner should decide on protection for steel casing or tracer wire; For work in Brazoria County’s fine sandy loam, we account for the fact that HDPE is not subject to that soil corrosion concern. The geologic map shows the Beaumont Formation, areas predominantly clay, of Pleistocene age. Its clay and mud favor controlled fluid pressure.

How do we drill Damon’s clay ground?

At about 40 inches, the USDA soil survey maps clay across Damon, including ground below Edna fine sandy loam. We shape the drilling plan around sticky soil, a shallow seasonal water table and the route along streets such as Pipeline Road.

  1. Because Damon soil is heavy clay at about 40 inches, we use thinner drilling fluid with polymer and ream in stages to limit clay buildup on the reamer.
  2. Sticky clay can swell around pipe, so on a route such as Pipeline Road we aim to pull the pipe the same day the hole is opened.
  3. The USDA survey maps a seasonal water table within 60 inches across Damon, so we plan small pits and pumping where water fills an excavation.
  4. Before drilling near Stockwell Street, we hydrovac pothole each marked utility; surface paint does not show its depth, so we check it before the drill approaches.
Open bore pit in red Oklahoma dirt with white PVC conduit stub ups and an orange safety barrier
An open bore pit in red Oklahoma dirt with PVC conduit stubbed up and a safety barrier around it.

What might a new line cross near Cow Creek in Damon?

Texas State Highway 36 has 1.1 mapped roadway miles inside the Damon community boundary, and there are no other highways mapped within 1.5 miles outside it. A line crossing the state highway needs a bore plan that accounts for its right of way and pavement. Pipeline Road is the longest named street in the community at 1.09 miles, followed by Woodward Street at 0.95 miles and Mulcahy Avenue at 0.92 miles. Stockwell Street is another route to check for access and marked utilities.

CrossingTypeMapped extentWho has a say
Texas State Highway 36State highway1.1 roadway miles insideState highway office
Cow CreekStream nearby0.5 miles outsideChecked for Corps of Engineers jurisdiction
Swipe the table sideways to see every column.

No railroad is mapped inside the Damon community boundary or within one mile outside it, so no local track crossing is identified. Cow Creek is 0.5 miles from the boundary, rather than inside it. No named streams or lakes and ponds are mapped inside the community, and no mapped street crossings of named streams are identified there. If a planned route reaches Cow Creek, the crossing is checked for U.S. Army Corps of Engineers jurisdiction during planning.

Who approves a Damon bore in Brazoria County?

Damon is an unincorporated community, so its public streets are not under a city government. For work in the right of way of Texas State Highway 36, the utility that owns the line applies for a TxDOT utility permit through the online RULIS system. The TxDOT Houston District reviews it. For Texas State Highway 36 crossings, we prepare the bore plan and profile and work under the utility owner’s TxDOT Houston District permit. No railroad is mapped near the community, but a future track crossing would require an agreement with the railroad that owns the track. A planned crossing at Cow Creek is checked for Corps jurisdiction.

Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.

Who owns lines already in the ground in Brazoria County near Damon?

The water provider for a specific Damon address has to be confirmed with the county or the local water district before a bore is planned. EPA drinking water records do not tie a system to Damon by name, so the provider cannot be matched from those records. For work in Brazoria County, we coordinate around service reported by CenterPoint Energy, Texas New Mexico Power and Jackson Electric Cooperative. That does not establish which company serves a particular address, so the line owner needs to be confirmed before we plan an electric conduit bore along Stockwell Street.

Line ownerWhat it isSourceSize
CenterPoint Energy, Texas-New Mexico Power and Jackson Electric CooperativeElectric utilities reporting service in Brazoria CountyEIA Form 861Confirm the line owner by address
Swipe the table sideways to see every column.

Damon’s median housing year is 1983 in the 2019 to 2023 five year estimates, so we plan underground work with utility coordination in mind. Of 86 housing units, 9 percent were built before 1960, 53 percent from 1960 to 1999 and 38 percent in 2000 or later. That mix can mean work for a replacement line as well as a new service, but the existing route has to be checked. Before a bore near older lines along Woodward Street, we use hydrovac potholing to expose marked utilities; paint shows position, not depth.

Reel of yellow polyethylene gas pipe on a trailer staged for a directional bore
A reel of yellow polyethylene gas pipe on a trailer, staged for a directional bore.

Where is Damon in relation to Rosenberg?

Damon is an unincorporated community in Brazoria County, at an elevation of 106 feet and with a land area of 1.39 square miles. Its ZIP code is 77430. Needville is 9.7 miles northwest, Fairchilds is 10.8 miles north and West Columbia is 11.2 miles southeast. Rosenberg, the nearest larger city, is 19.1 miles north; Angleton, the county seat, is 20.3 miles east. The trip from our Yukon yard is 494 road miles and 9.8 drive hours, which affects mobilization for a Damon job.

Places near Damon

What would we bore near Pipeline Road in Damon?

  • Highway crossing: A line beneath Texas State Highway 36 needs a bore route through the state right of way that keeps the pavement intact.
  • Water service: A service along Pipeline Road starts with confirming the address specific water provider and locating existing lines before drilling.
  • Fiber conduit: A conduit route near Stockwell Street needs marked utilities exposed before the drill head enters Damon’s mapped clay.
  • Sewer line: A sewer bore along Woodward Street can avoid an open cut across the surface, with pits placed off the traveled route.
  • Creek crossing: If a project route reaches Cow Creek, we plan the channel crossing and check Corps jurisdiction during planning.

More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.

What do you need to quote a Damon bore under Texas State Highway 36?

For a Texas State Highway 36 crossing, tell us where the work is with an address or map pin. Then say what goes in the ground, such as a water line or fiber conduit near Pipeline Road. On Pipeline Road, we ask for the pipe or conduit size and footage so we can scope the bore accurately. A sketch or plans help us see the route, access and nearby crossings.

In Damon, the heavy clay mapped below the surface is a leading cost factor because it affects reaming and fluid control. Length and pipe or conduit size shape the equipment and time needed. We also account for marked utilities that must be exposed, pavement at Texas State Highway 36, and any creek crossing near Cow Creek. Pits, excavator time and sand backfill can add to the work. At 494 road miles from Yukon, mobilization matters too; high profile or emergency work can change the scope.

Questions people ask about boring in Damon

Does Trinity take directional boring jobs in Damon, Brazoria County, and who staffs them?

Yes. Trinity takes directional boring work in Damon, and the 2020 Census counted 436 people in the community. Our own crews or crews from satellite yards run by partner drilling contractors we have vetted may do the field work. You work with Trinity from the first call through the bore log, including on a line along Pipeline Road.

Will groundwater or flood prone ground near Cow Creek cause trouble for Damon bore pits?

It can affect pit planning. The USDA soil survey maps a seasonal water table within 60 inches throughout Damon, so a pit near the route may need pumping. Flood prone soils are not mapped in the community. Cow Creek is 0.5 miles from the mapped boundary, and a planned stream crossing is checked for Corps jurisdiction.

Does Edna soil in Damon corrode steel, and what pipe should I use?

The USDA soil survey maps high steel corrosion risk throughout Damon, so the line owner should choose any coating for steel casing or tracer wire. For work in Brazoria County’s fine sandy loam, we account for the fact that HDPE is not subject to that soil corrosion concern. Edna soil covers 73 percent of the mapped community, but the final material choice should fit the line and the specific route.

What ground will a bore pass through in Damon where Edna soil is mapped?

The USDA soil survey maps Edna across 73 percent of Damon and Bernard across 27 percent. Fine sandy loam is the surface texture across 70 percent, but clay is mapped about 40 inches down throughout the area. That deeper heavy clay can stick to the reamer and grip pipe, so the drilling fluid and reaming sequence matter.

With Edna and Bernard soils in the area, will a directional bore in Damon hit rock?

Bedrock is not mapped in the top five feet of Damon, though that does not rule out rock deeper down. The geologic map shows the Beaumont Formation, areas predominantly clay, of Pleistocene age. Along a route such as Stockwell Street, actual ground conditions still need to be checked as the bore is planned.

Who approves a bore under Texas State Highway 36 in Damon?

The line owning utility applies for a TxDOT utility permit through the online RULIS system, and the TxDOT Houston District reviews it. We provide the bore plan and profile and work under the utility owner’s permit. This process applies to a right of way crossing of Texas State Highway 36 in Damon.

What bore sizes and lengths can Trinity handle near Stockwell Street in Damon?

We handle lines from 3/4 inch service lines up to 48 inch casing, and bore lengths from 10 feet to 5,000 feet. The right size and length for Stockwell Street depend on what the line serves, the route and the mapped clay. Send a sketch or plans if you have them.

How much notice does Texas811 need before a Damon bore on Pipeline Road, and what if marks move?

For work near Pipeline Road, request a locate at least 48 hours before excavation, excluding Saturdays, Sundays and legal holidays, and no earlier than 14 days before it. For a Texas State Highway 36 permit, if the start slips more than 14 days past the original notice, we make a new request. Have worn or moved marks refreshed through Texas811 before work continues.

What affects the cost of a directional bore under Texas State Highway 36 in Damon?

Whether the bore follows Old Guy Road or another route, we set the price from the job scope. In Damon, heavy clay, bore length and line size are key factors, along with utilities that must be exposed and pavement at Texas State Highway 36. Pits, excavator time, sand backfill, creek crossings near Cow Creek and mobilization from Yukon also affect the work.

Where the Damon facts on this page come from

Darren Rice in a safety vest at the bore pit beside the Trinity Boring Solutions Ditch Witch directional drill, with drill rods racked, on the airfield at Will Rogers World Airport in Oklahoma City

About Trinity Boring Solutions

Trinity Boring Solutions is a family business in Yukon, Oklahoma, founded by Dean Rice in 1965 and owned today by Darren Rice, who started its directional boring side in 1982. The company bores across Oklahoma and Texas. No bore is too big or too small: 4 foot sidewalk sleeves to roughly 4,100 feet under the Arkansas River in Tulsa. Reach us at (405) 409-7423.

Get a Quote for a Bore in Damon

Send the address, what is going in, the size and the footage.

Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com

Trinity Boring Solutions | 24/7 Available ☎ Call (405) 409-7423 Free Quote

Free Bore Planner

Plan Your Bore in Damon, Texas

Type the address of your job in Damon. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.

Talk to the crew that does the work

Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.

Call (405) 409-7423

Answered by a person, not a call center.

Would rather not call? Send the details and we will come back with a written quote.

Quick Quote In Page

County and State Pages for Damon

Same county: Pearland · Alvin · Lake Jackson · Angleton · Manvel · Iowa Colony · Clute · Freeport · Richwood · Sweeny · Brazoria · Wild Peach Village. All counties: Texas county list.