trinityboringsolutions.com

Sand Springs Texas Directional Boring: Amarillo Soil, Interstate 20 and Sandy Hollow

Quick Answer: Midway Road, Moss Lake Road and Salem Road lead the named streets across 20.37 public road miles, with Interstate 20 running through Sand Springs. We take directional boring, also called horizontal directional drilling (HDD), for routes beneath that highway and other crossings. Our Yukon, Oklahoma main office is 380 road miles away, and Union Pacific track is another mapped crossing to plan around. Amarillo loamy fine sand dominates the mapped soil, where loose sand can cave behind the bit. Staged reaming helps hold an Amarillo sand bore open.

Family Business Since 1965 Boring Since 1982 24 Hour Phone No Utility Strike in 25 Years

Sand Springs bores at a glance

  • Unincorporated community in Howard County, Texas. Population 878 (2020 Census count).
  • Road distance from our Yukon, Oklahoma main office: 380 miles, about 7.5 hours of driving.
  • Ground: Amarillo soil is mapped on 35 percent of the area, with sandy clay loam about 40 inches down.
  • Rock: no bedrock is mapped in the top 60 inches.
  • Highways inside the boundary: Interstate 20. State permit office: TxDOT Abilene District.
  • Railroad track inside the boundary: Union Pacific, with 1 mapped street and rail crossings.
  • Named streams inside the boundary: Sandy Hollow.
  • Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
  • Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
  • Phone answered 24 hours a day: (405) 409-7423

Who does directional boring near Midway Road in Sand Springs?

Sand Springs is an unincorporated community in Howard County, where the 2020 Census counted 878 residents; the Census Bureau does not publish yearly estimates for unincorporated places. Along Midway Road or Moss Lake Road, our crews can bore water, sewer, gas, electric conduit and fiber routes beneath pavement, driveways or other surface crossings without cutting the route open.

Our main office is in Yukon, Oklahoma, and Sand Springs work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. A short service bore off Salem Road can use 3/4 inch line, while a major crossing can call for 48 inch casing; our range covers bore lengths from 10 feet to 5,000 feet. Trinity is a family business dating to 1965, and we have done directional boring since 1982, including work across Texas.

Trinity Boring Solutions branded compact directional drilling unit positioned beside a tree on a red dirt jobsite
Our compact directional drill set up beside a tree on a tight site. Photos on this page are from our jobs in Oklahoma and Texas.

What is Amarillo soil like to bore in Sand Springs?

The USDA soil survey maps Amarillo soil across 35% of Sand Springs, followed by Springer at 24%, Brownfield at 13% and Circleback at 11%. At about 40 inches down, sandy clay loam is mapped under 57% of the area, while fine sandy loam accounts for 24%. The survey also maps 60% of the area as sandy at that depth and gives an average clay content of 18%. These are mapped soil patterns, not test borings; expect the route to vary, with sand that can cave behind the drill head and clay that can grip the pipe.

USDA soil survey, inside the Sand Springs mapped community boundaryWhat is mapped
Soil series mappedAmarillo 35 percent, Springer 24 percent, Brownfield 13 percent, Circleback 11 percent and Patricia 7 percent
Texture at the surfaceloamy fine sand 50 percent, fine sand 31 percent and fine sandy loam 15 percent
Texture about 40 inches downsandy clay loam 57 percent, fine sandy loam 24 percent and fine sand 11 percent
Engineering class about 40 inches downclayey sand (SC) 46 percent, silty clayey sand (SC SM) 24 percent and silty sand (SM) 11 percent
Average clay content about 40 inches down18 percent
Bedrock mapped within 60 inchesNone mapped
Seasonal water table within 60 inches0 percent of the area
Flood prone soils0 percent of the area
High corrosion risk for uncoated steel0 percent of the area

For Sand Springs, the soil survey places no bedrock within its mapped upper five feet; that does not rule out rock deeper down. It also maps no seasonal water table within 60 inches, no flood prone soils and no areas of high steel corrosion risk. The geology map identifies Holocene Sand sheet deposits, including windblown sand, as well as Triassic sedimentary units of Mesozoic age. Sandy Hollow still calls for a site specific crossing review, and actual ground conditions along a bore may differ from the mapped pattern.

What does it take to bore sandy clay loam in Sand Springs?

Sand Springs has sandy surface soils and sandy clay loam mapped at about 40 inches. We plan the bore around both: sand needs support to keep the hole open, while clay calls for controlled fluid and a steady pullback.

  1. At Amarillo loamy fine sand, we use drilling fluid to help support the hole, then ream in stages so loose material is less likely to cave behind the bit.
  2. Where sandy clay loam is mapped about 40 inches down, we adjust fluid and reaming to limit clay buildup and avoid leaving an open hole longer than needed.
  3. Before drilling near a marked route on Midway Road, we hydrovac pothole each utility on the path; locate paint shows position, not burial depth.
  4. At a Sandy Hollow crossing, we track the drill head from the surface and record depth and pitch as the bore advances, keeping the channel bank uncut.
Bobcat E35 mini excavator lowering a 6 inch PVC sleeve into a bore pit in sandy soil at NE 24th Street in northeast Oklahoma City
Lowering a 6 inch PVC sleeve into a bore pit in sandy soil at NE 24th Street in Oklahoma City.

What is in the way of a new line in Sand Springs near Interstate 20?

Interstate 20 crosses Sand Springs, with 5.2 mapped roadway miles inside the community boundary. Midway Road is the longest named street at 2.56 miles, followed by Moss Lake Road at 1.03 miles and Salem Road at 1.02 miles. Across 20.37 public road centerline miles, a route may meet local pavement as well as the interstate corridor. Boring beneath existing highway pavement avoids opening the surface, and the exact alignment determines where pits and utility checks belong.

CrossingTypeMapped extentWho has a say
Interstate 20Interstate5.2 roadway miles insideState highway office
Union PacificRailroad1.63 track miles insideThe railroad
Sandy HollowStream1.26 channel miles insideChecked for Corps of Engineers jurisdiction
Swipe the table sideways to see every column.

Union Pacific has 1.63 track miles in Sand Springs on the Toyah Subdivision, and one street and rail crossing is mapped. A rail bore needs the railroad owner’s crossing agreement, whose terms set details such as casing, depth and flagging. Sandy Hollow runs for 1.26 channel miles, with three mapped street crossings of named streams. The crossing plan should account for the creek route; no lakes or ponds are mapped within one mile.

Do I need a permit to bore under Interstate 20 in Howard County in Sand Springs?

Sand Springs has no city government, so street authority is with Howard County or the state, depending on the road. Interstate 20 is a TxDOT route, reviewed by the TxDOT Abilene District. For work in its right of way, the utility owner files the utility permit through TxDOT’s RULIS system; we prepare the bore plan and profile and work under the owner’s permit. TxDOT rules set crossing cover by line type, including 60 inches for electric, communication and water lines, and pressurized sewer lines; the district may set a different depth. A Union Pacific crossing also needs the railroad’s agreement, and Sandy Hollow is checked for Corps jurisdiction during planning.

Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.

Which utilities have lines in Sand Springs and Howard County?

The water provider for a specific Sand Springs address has to be confirmed with Howard County or the local water district before a bore is planned. For a Midway Road route, that means identifying the provider and its line before setting the path. Oncor Electric Delivery Company and Lyntegar Electric Cooperative report electric service in Howard County, but the owner at an individual address must be confirmed before planning an electric conduit bore. Hydrovac potholes expose marked lines so the water route and electric conduit can be steered around actual depths.

Line ownerWhat it isSourceSize
Oncor Electric Delivery Company and Lyntegar Electric CooperativeElectric utilities reporting service in Howard CountyEIA Form 861Confirm the line owner by address
Swipe the table sideways to see every column.

American Community Survey 2019 to 2023 five year estimates put Sand Springs housing’s median year built at 1975: 18% of units were built before 1960, 54% from 1960 to 1999, and 28% in 2000 or later. A Salem Road project could involve replacement of older pipe or a service for newer housing, so the route matters more than the age pattern alone. Before drilling near marked utilities, we hydrovac each one on the bore path; paint shows position, not depth.

Yellow polyethylene gas pipe pulled through a directional bore beside a commercial building
Yellow polyethylene gas pipe pulled through a directional bore beside a commercial building.

How far is Sand Springs from Coahoma and the Yukon yard?

Sand Springs is an unincorporated community in Howard County, at an elevation of 2,422 feet and covering 2.57 square miles. Its ZIP code is 79720. Coahoma is 2.5 miles northeast, while Big Spring is 8.6 miles west and is both the county seat and the nearest larger city. Forsan is 11.8 miles south. From the Yukon, Oklahoma yard, the drive is 380 road miles and 7.5 hours, which is part of planning equipment mobilization for a Midway Road job.

Places near Sand Springs

What kinds of bores come up near Moss Lake Road in Sand Springs?

  • Highway crossing: An Interstate 20 bore is planned beneath the existing pavement, with the route and pits set outside the travel lanes.
  • Water service: A line near Midway Road needs the address specific water provider confirmed before we set its bore path.
  • Fiber route: A fiber bore along Moss Lake Road can pass beneath pavement without opening a trench across the street.
  • Creek crossing: A Sandy Hollow bore needs a profile planned for the channel and a check for Corps jurisdiction during planning.
  • Rail crossing: A bore beneath the Union Pacific Toyah Subdivision requires the railroad owner’s agreement and its crossing conditions.
  • Electric conduit: Near Salem Road, we identify the electric line owner before setting a conduit route past marked utilities.

More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.

What should I send for a Sand Springs quote near Union Pacific?

A map pin matters near Union Pacific track or Sandy Hollow because a small shift can change the crossing and the permit path. Send the Sand Springs address or pin, what will go underground, the pipe or conduit size and the footage. A sketch or plans help us see how the route meets Midway Road, the creek or another marked feature.

The route’s Amarillo loamy fine sand and sandy clay loam affect drilling fluid and reaming. Crossings of Interstate 20, Union Pacific track or Sandy Hollow add different planning and exposure needs, while pavement, pits, excavator time and sand backfill also shape the work. Mobilization from the Yukon yard is part of the logistics for Sand Springs, 380 road miles away. Length, line size, utility exposure and emergency timing all depend on the scope at the actual address.

Questions people ask about boring in Sand Springs

Does Trinity take directional boring work in Sand Springs, Howard County?

Yes. We take directional boring work in Sand Springs, and Trinity stays responsible for the project whether our own crews or a vetted partner contractor works at the site. From the first call to the bore log, you deal with Trinity. For a Howard County job near Midway Road, send the proposed route and line details so we can plan the scope.

Who approves a Sand Springs bore under Interstate 20?

TxDOT reviews Interstate 20 work through its Abilene District. The utility owner, not the drilling contractor, submits the utility permit application in TxDOT’s RULIS system. We prepare the bore plan and profile for the filing and work under the permit issued to the owner. The required depth depends on the line type and the permit conditions.

What does a Sand Springs bore under Union Pacific track need?

A crossing beneath the Union Pacific Toyah Subdivision needs an agreement from the railroad that owns the track. That agreement sets the crossing requirements, including casing, depth and flagging. Since 1.63 track miles are mapped in Sand Springs, the route must be checked against the actual track location before the bore plan is settled.

Can a Sand Springs line be bored under Sandy Hollow?

A bore can be planned beneath Sandy Hollow, subject to the site and crossing review. The stream runs 1.26 channel miles through Sand Springs, so the profile must account for the channel rather than placing an open trench across it. The crossing is also checked for U.S. Army Corps of Engineers jurisdiction during planning.

Who owns electric lines for a Sand Springs project in Howard County?

Oncor Electric Delivery Company and Lyntegar Electric Cooperative report electric service in Howard County, but that does not establish the owner at a particular Sand Springs address. Confirm the line owner and conduit requirements for the route before planning the bore. Near Salem Road, we expose marked utilities by hydrovac before drilling close to them.

Does Sand Springs or Howard County control Salem Road, and must it be cut?

Sand Springs is unincorporated and has no city government, so the road authority is the county or state rather than a city government. A bore beneath Salem Road can leave the pavement uncut, with pits placed off the roadway where the site allows. The road’s authority and route conditions need to be established for the specific job.

What bore sizes and lengths can Trinity handle near Vikki Road in Sand Springs?

Our range runs from 3/4 inch service lines to 48 inch casing, with bore lengths from 10 feet to 5,000 feet. For a Vikki Road project, the needed size and footage depend on what the line carries and what it must cross. A map pin and sketch help us assess the actual route.

How much notice does Texas811 need for a Sand Springs bore near Midway Road?

Texas law requires a locate request at least 48 hours before excavation, excluding Saturdays, Sundays and legal holidays; Texas811 describes this as at least two working days. A request cannot be made more than 14 days before excavation. If the start slips more than 14 days past the original notice, make a new request, and have worn or moved marks refreshed through Texas811 before work continues near Midway Road.

What affects the cost of directional boring in Sand Springs near Interstate 20?

The route, line size and length all matter, as do soil, utility crossings, pavement, creek work, pits and mobilization. Amarillo loamy fine sand may require staged reaming, while Interstate 20 or Union Pacific crossings add planning needs. The 380 road miles from the Yukon yard also affect logistics for a Sand Springs job.

Where the Sand Springs facts on this page come from

Darren Rice in a safety vest at the bore pit beside the Trinity Boring Solutions Ditch Witch directional drill, with drill rods racked, on the airfield at Will Rogers World Airport in Oklahoma City

About Trinity Boring Solutions

Trinity Boring Solutions is a family business in Yukon, Oklahoma, founded by Dean Rice in 1965 and owned today by Darren Rice, who started its directional boring side in 1982. The company bores across Oklahoma and Texas. No bore is too big or too small: 4 foot sidewalk sleeves to roughly 4,100 feet under the Arkansas River in Tulsa. Reach us at (405) 409-7423.

Get a Quote for a Bore in Sand Springs

Send the address, what is going in, the size and the footage.

Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com

Trinity Boring Solutions | 24/7 Available ☎ Call (405) 409-7423 Free Quote

Free Bore Planner

Plan Your Bore in Sand Springs, Texas

Type the address of your job in Sand Springs. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.

Talk to the crew that does the work

Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.

Call (405) 409-7423

Answered by a person, not a call center.

Would rather not call? Send the details and we will come back with a written quote.

Quick Quote In Page

County and State Pages for Sand Springs

All counties: Texas county list.