trinityboringsolutions.com

Sandia Texas Directional Boring: Papalote Soil, FM 1540 and Lain Creek

Quick Answer: FM 1540 is one route a bore may pass beneath, and Trinity provides directional boring, also called horizontal directional drilling (HDD), in Sandia, Texas. Dolch Street and Porter Mae Avenue are among its longest named streets. Sandia is 570 road miles from our Yukon main office, a factor for FM 70 mobilization. Papalote loamy fine sand covers 74 percent of the mapped surface, so the hole needs support against sloughing. At about 40 inches, sandy clay loam is common and clay can grip pipe.

Family Business Since 1965 Boring Since 1982 24 Hour Phone No Utility Strike in 25 Years

Sandia bores at a glance

  • Unincorporated community in Jim Wells County, Texas. Population 326 (2020 Census count).
  • Road distance from our Yukon, Oklahoma main office: 570 miles, about 11.1 hours of driving.
  • Ground: Papalote soil is mapped on 74 percent of the area, with sandy clay loam about 40 inches down.
  • Rock: no bedrock is mapped in the top 60 inches.
  • Highways inside the boundary: FM 1540, FM 70 and Texas State Highway 359. State permit office: TxDOT Corpus Christi District.
  • Railroad track inside the boundary: none mapped.
  • Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
  • Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
  • Phone answered 24 hours a day: (405) 409-7423

Who handles directional boring near FM 1540 in Sandia?

We take directional boring and horizontal directional drilling work in Sandia, an unincorporated community in Jim Wells County. The 2020 Census counted 326 people here; the Census Bureau does not publish yearly estimates for unincorporated places. We install water, sewer, gas, electric conduit and fiber lines, including service routes running along Dolch Street or crossing FM 1540.

Our main office is in Yukon, Oklahoma, and Sandia work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. Our family business began in 1965, and we have focused on directional boring since 1982. For a service line along Porter Mae Avenue or a larger casing beneath FM 1540, our equipment handles 3/4 inch service lines up to 48 inch casing.

Aerial view of a bore pit with drill rig and conduit alongside a directional drill rig and conduit on a concrete lot
Our crew at a bore pit beside the directional drill on a conduit job, seen from above. Photos on this page are from our jobs in Oklahoma and Texas.

How does Papalote soil affect drilling in Sandia?

The USDA soil survey maps Papalote series across 74 percent of Sandia, with Papalote loamy fine sand, 0 to 3 percent slopes, covering the same share of mapped area. Fine sandy loam accounts for 19 percent of the surface texture and clay for 7 percent. At about 40 inches below the surface, sandy clay loam is mapped across 93 percent of the area, with clay in the rest. Our mapped Papalote, Opelika, Runge, and Banquete soil patterns guide planning, but they are not test borings. The loamy fine sand near Dolch Street can cave behind the drill, while deeper clay can cling to a reamer or pipe.

USDA soil survey, inside the Sandia mapped community boundaryWhat is mapped
Soil series mappedPapalote 74 percent, Opelika 8 percent, Runge 7 percent and Banquete 6 percent
Texture at the surfaceloamy fine sand 74 percent, fine sandy loam 19 percent and clay 7 percent
Texture about 40 inches downsandy clay loam 93 percent and clay 7 percent
Engineering class about 40 inches downlean clay (CL) 90 percent and fat clay (CH) 7 percent
Average clay content about 40 inches down32 percent
Bedrock mapped within 60 inchesNone mapped
Seasonal water table within 60 inches9 percent of the area
Flood prone soils0 percent of the area
High corrosion risk for uncoated steel9 percent of the area

For FM 70 crossings, we see no mapped bedrock in Sandia’s top five feet, though deeper rock remains possible. The USDA soil survey maps a seasonal water table within 60 inches across 9 percent of the area, so pits may need pumping where that condition occurs. Near Lain Creek, we plan with the map showing no flood prone soils in Sandia. High steel corrosion risk covers 9 percent, which can matter for steel casing or tracer wire; the line owner selects materials. The geologic map identifies Alluvium of Chibanian age, a mix of clay, gravel, sand and silt, so actual ground can vary along a bore.

What does it take to bore sandy clay loam in Sandia?

Sandia’s Papalote surface soils are sandy, while the mapped texture at about 40 inches is mostly sandy clay loam. We adjust fluid and reaming to the ground along each route.

  1. We plan for Papalote loamy fine sand near Dolch Street to fall in behind the bit, using drilling fluid and staged reaming to support the open hole.
  2. At about 40 inches, sandy clay loam is mapped across most of Sandia, so we adjust fluid and reaming to limit clay buildup on the reamer.
  3. Before a bore near Meta Street, we hydrovac pothole every marked utility on the route; paint gives position, not depth.
  4. Where a seasonal water table occurs in Sandia’s mapped soils, we keep pits small and pump as needed, then track the drill head and log depth and pitch.
Open bore pit in red Oklahoma dirt with white PVC conduit stub ups and an orange safety barrier
An open bore pit in red Oklahoma dirt with PVC conduit stubbed up and a safety barrier around it.

Where might a Sandia bore pass beneath Dolch Street?

FM 1540, FM 70 and Texas State Highway 359 run inside the mapped community boundary, with 1.8, 1.0 and 0.8 roadway miles there, respectively. No listed highway lies within 1.5 miles outside the boundary. Dolch Street is the longest named street at 0.57 miles, followed by Porter Mae Avenue at 0.49 miles and Portermen Avenue at 0.36 miles. Those routes can shape a bore plan where a new water, sewer or conduit line needs to cross pavement rather than cut it.

CrossingTypeMapped extentWho has a say
FM 1540State highway1.8 roadway miles insideState highway office
FM 70State highway1 roadway miles insideState highway office
Texas State Highway 359State highway0.8 roadway miles insideState highway office
Lain CreekStream nearby0.4 miles outsideChecked for Corps of Engineers jurisdiction
Nueces RiverStream nearby1 miles outsideChecked for Corps of Engineers jurisdiction
Lake Corpus ChristiLake or pond1,403 acres, nearbyChecked for Corps of Engineers jurisdiction
Swipe the table sideways to see every column.

No railroad is mapped inside Sandia or within 1 mile outside its boundary, so there is no mapped track route to plan around. No named stream runs inside the community, and no street crossing of a named stream is mapped there. Lain Creek is 0.4 miles from the boundary and the Nueces River is 1.0 mile away; Lake Corpus Christi is also within 1 mile. A proposed crossing near Lain Creek or the lake needs water crossing review during planning.

Who approves Sandia work on roads in Jim Wells County?

Sandia is an unincorporated census designated place with no city government, so a permit for work on FM 1540, FM 70 or Texas State Highway 359 goes through TxDOT, not a city office. The TxDOT Corpus Christi District reviews the utility permit. For electric or communication lines crossing one of these highways, the required cover is at least 60 inches below the lowest point of the crossed grade; water lines need 60 inches, and pressurized sewer lines need 60 inches. The utility owner submits the application through RULIS, while we prepare the bore plan and profile and work under that owner’s permit. A crossing planned near Lain Creek is checked for U.S. Army Corps of Engineers jurisdiction.

Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.

Whose buried lines must we check in Sandia, Jim Wells County?

The water provider for a specific address in Sandia has to be confirmed with the county or local water district before a bore is planned; the provider could not be matched to the place. AEP Texas Central, Nueces Electric Cooperative and San Patricio Electric Cooperative report service in Jim Wells County, but that does not identify the electric line owner at every address. We confirm the owner before planning a conduit bore near Meta Street or another route.

Line ownerWhat it isSourceSize
AEP Texas Central, Nueces Electric Cooperative and San Patricio Electric CooperativeElectric utilities reporting service in Jim Wells CountyEIA Form 861Confirm the line owner by address
Swipe the table sideways to see every column.

The American Community Survey 2019 to 2023 five year estimates put Sandia’s median housing year at 1992; 26 percent of homes were built before 1960, 41 percent from 1960 to 1999 and 33 percent in 2000 or later. That mix may mean replacing older lines as well as adding services near newer homes. Paint shows a marked line’s position, not its depth, so we hydrovac pothole every marked utility on the path before drilling near it, including a proposed route beneath Meta Street.

Coiled black HDPE conduit fitted with a pulling grip staged on a lawn along a completed bore path
Coiled HDPE conduit fitted with a pulling grip, staged on a lawn along a finished bore path.

What is near Sandia and Robstown?

Sandia is in Jim Wells County, covers 0.97 square miles and sits at an elevation of 123 feet. Its ZIP code is 78383. K-Bar Ranch is 4.1 miles southwest, Lake City is 4.4 miles north, Paisano Park is 5.1 miles north, Edgewater Estates is 5.2 miles north and Lakeside is 5.7 miles north. Robstown, the nearest larger city, is 19.8 miles southeast; Alice, the county seat, is 22.0 miles southwest. The Yukon yard is 570 road miles away, a drive of 11.1 hours, which factors into mobilization for work near FM 1540.

Places near Sandia

Which jobs could need a bore near Porter Mae Avenue in Sandia?

  • Highway crossing: A water line beneath FM 1540 needs a bore plan that accounts for TxDOT cover and the highway right of way.
  • Water service: A new service along Porter Mae Avenue needs an address specific route and confirmation of the provider serving that property.
  • Fiber conduit: A conduit route beneath Dolch Street can avoid cutting pavement, with each marked utility exposed before drilling near it.
  • Creek crossing: A proposed line near Lain Creek needs channel planning and a check for U.S. Army Corps of Engineers jurisdiction.
  • Electric conduit: A route near Meta Street starts with confirming the line owner, since several utilities report service in Jim Wells County.
  • Sewer line: A pressurized sewer crossing FM 70 needs a bore plan that accounts for the required highway cover.

More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.

What should I send to price a Sandia bore near Lain Creek?

For a quote near Lain Creek or Dolch Street, start with the address or a map pin and tell us what will go underground. Give us the pipe or conduit size and the footage. A sketch or plans showing the route across FM 1540 or along Porter Mae Avenue help us understand the work.

The 570 road miles from Yukon make mobilization part of a Sandia job’s scope. Papalote loamy fine sand and the clay mapped below it affect drilling and fluid needs, while a crossing of FM 1540 brings highway permitting and cover requirements into the plan. We also consider pipe size, footage, utilities to expose, pavement, pits, excavator time, sand backfill and any creek or drainage crossing near Lain Creek.

Questions people ask about boring in Sandia

Does Trinity take directional boring work in Sandia, Jim Wells County, and who does the work?

Yes. We take directional boring work in Sandia, and Trinity remains the customer’s contact from the first call through the bore log. Our own crews and satellite yards operated by drilling contractor partners we have vetted can handle work near FM 1540; the crew setup depends on the job.

What ground should I expect for a Sandia bore through Papalote soil?

The USDA soil survey maps Papalote loamy fine sand across 74 percent of Sandia’s area. At about 40 inches, sandy clay loam is mapped across 93 percent. The surface sand can cave behind the drill, while deeper clay can stick to the reamer or grip the pipe, so the route needs to be planned for changing ground.

Is a Sandia bore likely to hit rock near FM 70?

Bedrock is not mapped in Sandia’s top five feet, but that does not rule out deeper rock along a route near FM 70. The geologic map shows Alluvium of Chibanian age, made up of clay, gravel, sand and silt. A site specific bore plan still needs to account for conditions along the full path.

Who approves a Sandia bore beneath FM 1540?

The utility owner applies for the TxDOT utility permit through RULIS, and the TxDOT Corpus Christi District reviews it. On Texas State Highway 359, we provide the bore plan and profile and work under the permit issued to the utility owner. A line crossing FM 1540 must be planned to meet the applicable cover requirements or any depth set in the permit.

Can a line be bored beneath Lain Creek near Sandia?

A bore can be planned for a creek crossing, but the route needs review before work is set. Lain Creek lies 0.4 miles from Sandia’s mapped community boundary, and water crossings are checked for U.S. Army Corps of Engineers jurisdiction during planning. The crossing conditions and ground along the route guide the bore plan.

Which electric company owns the lines at my Sandia address in Jim Wells County?

County records show AEP Texas Central, Nueces Electric Cooperative and San Patricio Electric Cooperative reporting service in Jim Wells County; that does not establish which one serves a particular Sandia address. Confirm the line owner before planning a conduit bore near Porter Mae Avenue, then check conduit specifications with that owner.

What bore sizes and lengths can Trinity handle for a Sandia job near Meta Street?

We handle 3/4 inch service lines up to 48 inch casing, with bore lengths from 10 feet to 5,000 feet. For a proposed route near Meta Street, send the line type, size and estimated footage so we can match the equipment and plan to the work.

How early do I need to call Texas811 before a Sandia bore near Dolch Street, and what if marks move?

Texas law requires a locate request at least 48 hours before excavation, excluding Saturdays, Sundays and legal holidays, and no earlier than 14 days before it. Near Dolch Street, we allow the at least two working days that Texas811 describes for utility locating. If the start slips more than 14 days past the original notice, make a new request; have worn or moved marks refreshed through Texas811 before work continues near Dolch Street.

What affects the cost of directional boring in Sandia under FM 1540?

The route and work details determine the price, including footage, pipe or conduit size, Papalote soil conditions, utilities to expose, pavement, pits and equipment time. A crossing beneath FM 1540 also brings highway planning into the scope. The 570 road miles from Yukon affect mobilization, and a route near Lain Creek may add crossing planning.

Where the Sandia facts on this page come from

Darren Rice in a safety vest at the bore pit beside the Trinity Boring Solutions Ditch Witch directional drill, with drill rods racked, on the airfield at Will Rogers World Airport in Oklahoma City

About Trinity Boring Solutions

Trinity Boring Solutions is a family business in Yukon, Oklahoma, founded by Dean Rice in 1965 and owned today by Darren Rice, who started its directional boring side in 1982. The company bores across Oklahoma and Texas. No bore is too big or too small: 4 foot sidewalk sleeves to roughly 4,100 feet under the Arkansas River in Tulsa. Reach us at (405) 409-7423.

Get a Quote for a Bore in Sandia

Send the address, what is going in, the size and the footage.

Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com

Trinity Boring Solutions | 24/7 Available ☎ Call (405) 409-7423 Free Quote

Free Bore Planner

Plan Your Bore in Sandia, Texas

Type the address of your job in Sandia. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.

Talk to the crew that does the work

Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.

Call (405) 409-7423

Answered by a person, not a call center.

Would rather not call? Send the details and we will come back with a written quote.

Quick Quote In Page

County and State Pages for Sandia

Same county: Alice · Premont · Rancho Alegre · Orange Grove · San Diego · Coyote Acres · Alice Acres · Westdale · South La Paloma · Amargosa · Loma Linda East · Owl Ranch. All counties: Texas county list.