trinityboringsolutions.com

Elsa Texas Directional Boring: Hidalgo Soil, Texas State Highway 107 and Donna Drain

Quick Answer: Need a line beneath Texas State Highway 107 without cutting pavement? We do directional boring, also called horizontal directional drilling (HDD), for routes under that highway and Edinburg Avenue. From our Yukon, Oklahoma main office, Elsa is 702 road miles away, with FM 88 on the local route list. Hidalgo sandy clay loam is common here, so sticky cuttings can affect reaming and pullback.

Family Business Since 1965 Boring Since 1982 24 Hour Phone No Utility Strike in 25 Years

Elsa bores at a glance

  • Incorporated city in Hidalgo County, Texas. Population 5,750 (Census Bureau 2024 estimate).
  • Road distance from our Yukon, Oklahoma main office: 702 miles, about 13.7 hours of driving.
  • Ground: Hidalgo soil is mapped on 69 percent of the area, with clay loam about 40 inches down.
  • Rock: no bedrock is mapped in the top 60 inches.
  • Highways inside the boundary: Texas State Highway 107, FM 88 and FM 3071. State permit office: TxDOT Pharr District.
  • Railroad track inside the boundary: none mapped.
  • Public water: City of Elsa, surface water.
  • Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
  • Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
  • Phone answered 24 hours a day: (405) 409-7423

Does anyone do directional boring in Elsa and Hidalgo County?

Need a line under Edinburg Avenue without cutting the street? We take directional boring work in Elsa, an incorporated city in Hidalgo County with 5,750 residents, according to the Census Bureau Vintage 2024 estimate. Along Edinburg Avenue or Texas State Highway 107, our crews can place water, sewer, gas, electric conduit or fiber where the route calls for it.

Our main office is in Yukon, Oklahoma, and Elsa work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. For an Edinburg Avenue service, our range runs from a 3/4 inch service line to 48 inch casing, with bores from 10 feet to 5,000 feet. That range reflects a family business started in 1965, with directional boring work since 1982; the right setup for a Texas State Highway 107 crossing depends on the line and route.

Aerial view of a bore pit with drill rig and conduit alongside a directional drill rig and conduit on a concrete lot
Our crew at a bore pit beside the directional drill on a conduit job, seen from above. Photos on this page are from our jobs in Oklahoma and Texas.

What does the soil survey show beneath Elsa and Hidalgo soil?

The USDA soil survey maps Hidalgo soil across 69 percent of Elsa, with Hidalgo sandy clay loam making up 30 percent of the mapped area. Sandy clay loam is the surface texture across 67 percent, while clay loam accounts for 22 percent. About 40 inches down, the survey maps clay loam across 92 percent of the area and sandy clay loam across 8 percent; the mapped soil classification at that depth is CL throughout. Average clay content there is 32 percent, so cuttings can stay sticky and collect on the reamer. We treat mapped Hidalgo, Raymondville, and Racombes soil patterns as planning context, not test borings for work in Elsa.

USDA soil survey, inside the Elsa city limitsWhat is mapped
Soil series mappedHidalgo 69 percent, Raymondville 22 percent and Racombes 5 percent
Texture at the surfacesandy clay loam 67 percent, clay loam 22 percent and fine sandy loam 10 percent
Texture about 40 inches downclay loam 92 percent and sandy clay loam 8 percent
Engineering class about 40 inches downlean clay (CL) 100 percent
Average clay content about 40 inches down32 percent
Bedrock mapped within 60 inchesNone mapped
Seasonal water table within 60 inches8 percent of the area
Flood prone soils0 percent of the area
High corrosion risk for uncoated steel28 percent of the area

Bedrock is not mapped in the top five feet of Elsa, but that does not rule out rock deeper down. The geologic map shows stabilized sand dunes of Holocene age and alluvium of Chibanian age, with sand, silt and clay; local changes can affect the drill. Seasonal water tables are mapped within 60 inches in 8 percent of the area, while flood prone soils are not mapped. High steel corrosion risk covers 28 percent, so the line owner should consider casing and tracer wire materials; HDPE does not share that steel corrosion concern.

How do we drill Elsa clay loam without losing the bore path?

Elsa’s Hidalgo and Raymondville soils call for managing sticky cuttings and keeping fluid pressure under control. We adjust the reaming sequence to the mapped clay loam and the actual ground at the Edinburg Avenue route.

  1. Hidalgo sandy clay loam covers 30 percent of Elsa, so we use staged reaming and adjust the drilling fluid to keep sticky cuttings moving.
  2. With clay loam mapped across 92 percent of the area at about 40 inches, we plan the pullback soon after opening the hole to limit clay grip on the pipe.
  3. Where seasonal water tables are mapped near the surface, including within 40 inches in 1 percent of Elsa, we keep pits manageable and pump water if needed.
  4. Before a bore along Mile 16 N Road, we expose marked utilities with hydrovac, then track the drill head from the surface and log depth and pitch.
Drilling fluid returns at the entry as the Vermeer D24x40 S3 drills a 385 foot sandstone rock bore in Guthrie, Oklahoma
Drilling fluid coming back to the entry pit as our Vermeer D24x40 drills a 385 foot bore in Guthrie, Oklahoma.

What is in the way of a new line near Elsa’s Edinburg Avenue?

Texas State Highway 107 runs 3.6 mapped roadway miles inside Elsa, while FM 88 accounts for 1.9 miles and FM 3071 for 0.5 miles. A line beneath existing highway pavement needs a bored or tunneled crossing, not an open trench through the pavement. Edinburg Avenue is the city’s longest named street at 2.93 miles. Mile 16 N Road runs 2.01 miles, and Broadway Street runs 1.49 miles. Their lengths help identify the route, but plans and marked utilities determine the bore path.

CrossingTypeMapped extentWho has a say
Texas State Highway 107State highway3.6 roadway miles insideState highway office
FM 88State highway1.9 roadway miles insideState highway office
FM 3071State highway0.5 roadway miles insideState highway office
Donna DrainStream nearby0.8 miles outsideChecked for Corps of Engineers jurisdiction
Swipe the table sideways to see every column.

No railroad is mapped inside Elsa or within 1 mile outside the limits, and no mapped street and rail crossing is listed. Donna Drain lies 0.8 miles from the city limits; no named stream is mapped inside the city, and no street crossing of a named stream is mapped there. Elsa has 2.11 miles of unnamed drainage, so a route still needs a site check for drainage features. Around Donna Drain, mapped water features show no lakes or ponds within 1 mile, so we still verify crossings before boring.

Who has to sign off on Elsa work under Texas State Highway 107?

Edinburg Avenue is a city street, while Texas State Highway 107, FM 88 and FM 3071 are state highways. For work within state highway right of way, the utility owner applies through TxDOT’s online RULIS system; the TxDOT Pharr District reviews the application, and we prepare the bore plan and profile for the owner’s permit. TxDOT cover rules set the starting depth: electric and communication crossings need 60 inches below the lowest crossed grade, water crossings need 60 inches, and pressurized sewer crossings need 60 inches. Highway crossings are bored or tunneled beneath existing pavement. No railroad is mapped in Elsa. A Donna Drain crossing would be checked for U.S. Army Corps of Engineers jurisdiction during planning.

Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.

Which utilities should we check near the City of Elsa water lines?

The City of Elsa public water system uses surface water and serves 5,500 people through 2,194 service connections. That network is a key locate concern along streets such as Edinburg Avenue. AEP Texas Central, Oncor Electric Delivery Company and Magic Valley Electric Cooperative report electric service in Hidalgo County. Before planning an electric conduit bore on Texas State Highway 107, we confirm the line owner for the specific route rather than assume which provider serves the address.

Line ownerWhat it isSourceSize
City of ElsaPublic water systemSurface water2,194 connections, 5,500 people served
AEP Texas Central, Oncor Electric Delivery Company and Magic Valley Electric CooperativeElectric utilities reporting service in Hidalgo CountyEIA Form 861Confirm the line owner by address
Swipe the table sideways to see every column.

Elsa’s median housing year is 2000 in the American Community Survey 2019 to 2023 five year estimates, so we verify underground conditions along Edinburg Avenue. Six percent of homes were built before 1960, 44 percent from 1960 to 1999, and 50 percent in 2000 or later; that mix can mean both replacement work and new service routes near Mile 16 N Road. Before drilling near any marked utility, we expose it by hydrovac because paint shows position, not depth. For a line beneath Edinburg Avenue, that means potholing marked utilities along the bore path before the drill approaches.

Yellow polyethylene gas pipe pulled through a directional bore beside a commercial building
Yellow polyethylene gas pipe pulled through a directional bore beside a commercial building.

Where is Elsa in relation to La Blanca and nearby towns?

Elsa is in Hidalgo County, covers 2.09 square miles and sits at an elevation of 67 feet. Its ZIP code is 78543. La Blanca is 2.2 miles west, and Edcouch is 1.9 miles east. Weslaco is 9.5 miles south, while Edinburg, the county seat, is 10.0 miles west. From our Yukon, Oklahoma main office, Elsa is 702 road miles away, a 13.7 hour drive. Those distances matter when planning crew mobilization for a Texas State Highway 107 or Edinburg Avenue bore.

Places near Elsa

  • Edcouch: 1.9 miles east
  • La Blanca: 2.2 miles west
  • La Villa: 4.1 miles east
  • San Carlos: 4.3 miles west
  • Laguna Seca: 4.4 miles east
  • Directional boring in Weslaco: 9.5 miles south

What would we bore around Elsa’s Mile 16 N Road?

  • Highway crossing: A line under Texas State Highway 107 is bored beneath existing pavement, with the route and cover coordinated through the highway permit.
  • Water service: A connection near the City of Elsa system may need a route beneath Edinburg Avenue, with marked water lines exposed before drilling.
  • Fiber route: A fiber bore along Mile 16 N Road can pass below the street surface without cutting the pavement.
  • Drainage crossing: A proposed route near Donna Drain needs a site review and a check for U.S. Army Corps of Engineers jurisdiction during planning.
  • Electric conduit: Before placing conduit near FM 88, we confirm the line owner and expose marked utilities along the planned bore path.
  • Street service: A short service beneath Broadway Street can use entry and exit pits placed off the paved travel path.

More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.

What drives the price of an Elsa bore near Donna Drain?

For a route near Donna Drain or Edinburg Avenue, start with the address or map pin. Tell us what goes in the ground, such as water, fiber or electric conduit, then give the pipe or conduit size and the footage. A sketch or plans help us see the route, nearby pavement and any drainage crossing before we shape the bore plan.

In Elsa, soil and bore length are major price drivers because Hidalgo clay loam can change reaming and pullback time. Pipe or conduit size, marked utilities that need exposing, and pavement along Texas State Highway 107 also affect the work. A drainage crossing near Donna Drain can add planning, while pits, excavator time and sand backfill change site needs. Mobilization matters too: Elsa is 702 road miles from Yukon. On FM 88, we account for high profile or emergency work that can change the boring scope and require schedule adjustments.

Questions people ask about boring in Elsa

Does Trinity Boring Solutions take jobs in Elsa and Hidalgo County, and who staffs them?

Yes. We take directional boring work in Elsa, Hidalgo County, using our own crews and crews at satellite yards operated by partner drilling contractors we have vetted. You work with Trinity from the first call through the bore log, whether the crew is working near Edinburg Avenue or Texas State Highway 107.

What does Hidalgo soil in Elsa look like for a bore?

The USDA soil survey maps Hidalgo soil across 69 percent of Elsa, with clay loam across 92 percent of the area at about 40 inches. That mapped layer is classified CL and can produce sticky cuttings. It is a soil survey pattern, not a test boring, so the route near Mile 16 N Road still needs field assessment.

Will a bore in Elsa hit rock below the surface?

Bedrock is not mapped in Elsa’s top five feet, which does not rule out deeper rock. The geologic map identifies stabilized sand dunes and Chibanian alluvium made up of sand, silt and clay. A bore near Edinburg Avenue is planned to the site conditions rather than assuming one uniform layer.

For a bore under Texas State Highway 107 in Elsa, is the TxDOT Pharr District the state permit office to contact?

The utility owner applies for work in Texas State Highway 107 right of way through TxDOT’s RULIS system. The TxDOT Pharr District reviews the application. We prepare the bore plan and profile and work under the permit issued to the utility owner; cover and construction details are set for that crossing.

Can a line be bored beneath Donna Drain near Elsa?

A bore may be planned for a route near Donna Drain, but the site and channel conditions need review first. Donna Drain is 0.8 miles from Elsa’s city limits, and a water crossing is checked for U.S. Army Corps of Engineers jurisdiction during planning. The route and depth depend on the actual crossing.

Before boring near Donna Drain, who runs Elsa’s public water system, and where does its water come from?

The City of Elsa owns the public water system, which uses surface water. Public records list 2,194 service connections serving 5,500 people. Those water lines are important to locate before a new bore near Edinburg Avenue or a connection to the city system.

Does Trinity cover Edcouch and rural sites outside Elsa?

We take work across Texas, including routes around Edcouch and rural sites outside Elsa’s limits. Edcouch is 1.9 miles east of Elsa, so a project can extend beyond the city streets. We review the location and route to determine the crew plan and any road or utility crossings.

How much notice does Texas811 need for a bore along Edinburg Avenue in Elsa?

For an Edinburg Avenue bore, the locate request goes to Texas811 at least 48 hours before excavation begins, excluding Saturdays, Sundays and legal holidays, and no earlier than 14 days before work. For utility coordination on FM 3071, Texas811 describes the notice period as at least two working days before boring. If the start slips more than 14 days, submit a new request; worn or moved marks must be refreshed through Texas811 before work continues.

What affects the cost of a directional bore under Texas State Highway 107 in Elsa?

The route length, pipe or conduit size, and Hidalgo clay loam all affect the work, as do marked utilities, pavement and pit needs. A Texas State Highway 107 crossing adds highway planning, while a route near Donna Drain can require drainage review. Mobilization also matters because Elsa is 702 road miles from our Yukon, Oklahoma main office.

Where the Elsa facts on this page come from

Darren Rice in a safety vest at the bore pit beside the Trinity Boring Solutions Ditch Witch directional drill, with drill rods racked, on the airfield at Will Rogers World Airport in Oklahoma City

About Trinity Boring Solutions

Trinity Boring Solutions is a family business in Yukon, Oklahoma, founded by Dean Rice in 1965 and owned today by Darren Rice, who started its directional boring side in 1982. The company bores across Oklahoma and Texas. No bore is too big or too small: 4 foot sidewalk sleeves to roughly 4,100 feet under the Arkansas River in Tulsa. Reach us at (405) 409-7423.

Get a Quote for a Bore in Elsa

Send the address, what is going in, the size and the footage.

Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com

Trinity Boring Solutions | 24/7 Available ☎ Call (405) 409-7423 Free Quote

Free Bore Planner

Plan Your Bore in Elsa, Texas

Type the address of your job in Elsa. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.

Talk to the crew that does the work

Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.

Call (405) 409-7423

Answered by a person, not a call center.

Would rather not call? Send the details and we will come back with a written quote.

Quick Quote In Page

County and State Pages for Elsa

Same county: McAllen · Edinburg · Mission · Pharr · San Juan · Alton · Alamo · Mercedes · Donna · Palmview · Hidalgo · La Homa. All counties: Texas county list.