Cut and Shoot Texas Directional Boring: Lilbert Loamy Fine Sand, FM 1484 and Caney Creek
Quick Answer: Caney Creek and FM 1484 are crossings to plan around, and Trinity Boring Solutions takes directional boring, also called horizontal directional drilling (HDD), work in Cut and Shoot, Texas. Rolling Hills Road is 425 road miles from our Yukon, Oklahoma main office, so distance is part of mobilization planning. Lilbert loamy fine sand is mapped across 22 percent of the city, where loose sand can cave behind the drill and needs a supported hole.
Cut and Shoot bores at a glance
- Incorporated city in Montgomery County, Texas. Population 1,190 (Census Bureau 2024 estimate).
- Road distance from our Yukon, Oklahoma main office: 425 miles, about 8.2 hours of driving.
- Ground: Lilbert soil is mapped on 22 percent of the area, with loam about 40 inches down.
- Rock: no bedrock is mapped in the top 60 inches.
- Highways inside the boundary: FM 1484 and Texas State Highway 105. State permit office: TxDOT Houston District.
- Railroad track inside the boundary: none mapped.
- Named streams inside the boundary: Caney Creek, East Fork Crystal Creek and West Fork Crystal Creek.
- Public water: Town of Cut and Shoot, groundwater wells.
- Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
- Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
- Phone answered 24 hours a day: (405) 409-7423
Who handles directional boring near Caney Creek in Cut and Shoot?
Trinity Boring Solutions handles directional boring in Cut and Shoot, Montgomery County, where the Census Bureau Vintage 2024 estimate lists 1,190 residents. Caney Creek and FM 1484 are local features to plan around; we install water, sewer, gas, electric conduit and fiber along routes such as Rolling Hills Road and Willis Waukegan Road.
Our main office is in Yukon, Oklahoma, and Cut and Shoot work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. We are a family business started in 1965, and directional boring since 1982 means four decades of practice for ground like the Lilbert sand and clay mapped below it.

What ground should a bore expect in Cut and Shoot near Lilbert soil?
The USDA soil survey maps Lilbert loamy fine sand across 22 percent of Cut and Shoot, with Splendora fine sandy loam mapped across 19 percent. At about 40 inches below the surface, loam covers 33 percent of the mapped area, sandy clay loam 24 percent and clay 20 percent. Average clay content at that depth is 25 percent, while sandy ground accounts for 9 percent. For Cut and Shoot planning, we treat mapped patterns as general guidance, not test borings for a proposed bore route. The mix means the bore plan has to account for sand that can cave and finer ground that holds its shape.
| USDA soil survey, inside the Cut and Shoot city limits | What is mapped |
|---|---|
| Soil series mapped | Lilbert 22 percent, Splendora 19 percent, Conroe 18 percent, Segno 13 percent and Hatliff 8 percent |
| Texture at the surface | loamy fine sand 46 percent, fine sandy loam 33 percent and loam 9 percent |
| Texture about 40 inches down | loam 33 percent, sandy clay loam 24 percent and clay 20 percent |
| Engineering class about 40 inches down | clayey sand (SC) 38 percent, lean clay (CL) 37 percent and silty sand (SM) 9 percent |
| Average clay content about 40 inches down | 25 percent |
| Bedrock mapped within 60 inches | None mapped |
| Seasonal water table within 60 inches | 44 percent of the area |
| Flood prone soils | 9 percent of the area |
| High corrosion risk for uncoated steel | 44 percent of the area |
| Mapped as urban land (disturbed fill) | 3 percent of the area |
For Lilbert and other mapped soils, bedrock is not shown in the top five feet, though that does not rule out deeper rock. A seasonal water table is mapped within 60 inches across 44 percent of the area, so pits may need pumping; flood prone soils cover 9 percent, calling for care near Caney Creek. Mapped high steel corrosion risk covers 44 percent of Cut and Shoot, so we factor that area into underground work planning. The geologic map shows Alluvial pebble gravel and sand of Gelasian age, with unconsolidated gravel, sand, clay and silt. That mix calls for checking returns and keeping the hole supported.
How do crews bore Cut and Shoot loam and Lilbert soil?
In Cut and Shoot, we match the drilling method to Lilbert loamy fine sand and the loam and clay mapped below it, supporting the hole without washing out the route.
- Lilbert loamy fine sand can fall in behind the drill, so we use drilling fluid to support the hole and have the pipe ready before the final reaming pass.
- With clay mapped at about 40 inches under Cut and Shoot, we ream in stages and manage fluid so sticky cuttings do not collect on the tooling.
- Seasonal water tables are mapped within 60 inches across 44 percent of the area, so pits near Caney Creek may need pumping and a compact work footprint.
- At Rolling Hills Road, we hydrovac marked utilities before drilling near them, then track the drill head from the surface and log depth and pitch.

Which roads, tracks or creeks matter for Cut and Shoot near Rolling Hills Road?
FM 1484 and Texas State Highway 105 run through Cut and Shoot, with 6.1 mapped roadway miles of FM 1484 and 4.4 of Texas State Highway 105 inside city limits. Loop 336 is 0.2 miles outside the limits. Rolling Hills Road is the longest named street at 2.42 miles within the city; Willis Waukegan Road runs 1.76 miles and Millmac Road 1.7 miles. These routes help define access and crossing plans, while a bore can pass beneath pavement without cutting across it.
| Crossing | Type | Mapped extent | Who has a say |
|---|---|---|---|
| FM 1484 | State highway | 6.1 roadway miles inside | State highway office |
| Texas State Highway 105 | State highway | 4.4 roadway miles inside | State highway office |
| Loop 336 | Highway nearby | 0.2 miles outside | State highway office |
| BNSF Railway | Railroad nearby | 0.4 miles outside | The railroad |
| Caney Creek | Stream | 1.2 channel miles inside | Checked for Corps of Engineers jurisdiction |
| East Fork Crystal Creek | Stream | 1.14 channel miles inside | Checked for Corps of Engineers jurisdiction |
| West Fork Crystal Creek | Stream | 0.09 channel miles inside | Checked for Corps of Engineers jurisdiction |
| Mc Rae Creek | Stream nearby | 0.1 miles outside | Checked for Corps of Engineers jurisdiction |
| Cagle Branch | Stream nearby | 0.1 miles outside | Checked for Corps of Engineers jurisdiction |
| East for Crystal Creek | Stream nearby | 0.2 miles outside | Checked for Corps of Engineers jurisdiction |
| McRae Creek | Stream nearby | 0.4 miles outside | Checked for Corps of Engineers jurisdiction |
| Bart Lake | Lake or pond | 7 acres, nearby | Checked for Corps of Engineers jurisdiction |
No railroad runs inside Cut and Shoot, and no street and rail crossing is mapped in the city. BNSF Railway track is 0.4 miles outside the limits, so a route that reaches it needs coordination for a railroad crossing. Caney Creek runs 1.2 channel miles through the city, and East Fork Crystal Creek runs 1.14; four street crossings of named streams are mapped. Bart Lake, a 7 acre lake, is outside the city limits.
Do I need a permit to bore in Cut and Shoot, Montgomery County?
For a bore on Cut and Shoot city streets, the city has jurisdiction because Cut and Shoot is incorporated; FM 1484 and Texas State Highway 105 are state highways. Electric and communication lines crossing a highway need 60 inches of cover below the lowest crossed grade, and water lines need the same crossing cover; pressurized sewer lines also need 60 inches. TxDOT requires a utility permit for state highway right of way. The line owner files through RULIS, with the TxDOT Houston District reviewing it; we prepare the bore plan and profile for that filing. A crossing under BNSF Railway needs an agreement with the railroad, and Caney Creek is checked for Corps jurisdiction during planning.
Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.
What lines are near the Town of Cut and Shoot water system?
The Town of Cut and Shoot public water system uses groundwater wells and lists 1,961 service connections serving 6,000 people. Before an electric conduit bore near Rolling Hills Road, we confirm the line owner because CenterPoint Energy, Entergy Texas, Mid-South Electric Cooperative Association, Sam Houston Electric Cooperative and San Bernard Electric Cooperative report service in Montgomery County. Those reports do not identify the provider at every address, so the specific line has to be confirmed before the route is set.
| Line owner | What it is | Source | Size |
|---|---|---|---|
| Town of Cut and Shoot | Public water system | Groundwater wells | 1,961 connections, 6,000 people served |
| CenterPoint Energy, Entergy Texas, Mid-South Electric Cooperative Association, Sam Houston Electric Cooperative and San Bernard Electric Cooperative | Electric utilities reporting service in Montgomery County | EIA Form 861 | Confirm the line owner by address |
The American Community Survey 2019 to 2023 five year estimates put the median year built for Cut and Shoot housing at 1985; 10 percent was built before 1960, 54 percent from 1960 to 1999 and 36 percent in 2000 or later. That mix can mean replacement work as well as new service along FM 1484. Before the drill approaches a marked line, we expose it with hydrovac potholing; paint shows position, not depth. This matters around water connections and electric conduit alike.

What is near Cut and Shoot, including Grangerland?
Cut and Shoot is in Montgomery County, covers 2.71 square miles and sits at 181 feet elevation. We use ZIP codes 77303 and 77306 to identify the Cut and Shoot project area when planning underground work. Grangerland is 5.7 miles south, Deerwood is 3.0 miles southeast, and Conroe is 8.3 miles west; Conroe is also the county seat and nearest larger city. Rolling Hills Road and FM 1484 put local routes in view for planning. The city is 425 road miles and an 8.2 hour drive from our Yukon, Oklahoma yard, which affects mobilization for a Cut and Shoot job.
Places near Cut and Shoot
- Directional boring in Deerwood: 3 miles southeast
- Directional boring in Grangerland: 5.7 miles south
- Directional boring in Conroe: 8.3 miles west
- Directional boring in Woodloch: 9.1 miles southwest
- Directional boring in Panorama Village: 9.4 miles west
What boring work comes up in Cut and Shoot near Willis Waukegan Road?
- Highway crossing: A bore beneath FM 1484 can keep the roadway surface intact while the route passes under the travel lanes.
- Water service: A connection near the Town of Cut and Shoot system starts with confirming the service route and exposing marked lines.
- Fiber drop: A fiber route along Rolling Hills Road can use a narrow bore alignment to avoid opening the street surface.
- Creek crossing: A Caney Creek bore needs a planned path below the channel and a check for Corps jurisdiction.
- Rail crossing: A route toward BNSF Railway, 0.4 miles outside city limits, needs an agreement with the railroad owner.
- Electric conduit: Before planning a conduit route near Willis Waukegan Road, we confirm which reported Montgomery County electric provider owns the line.
More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.
What do you need to quote a Cut and Shoot bore near BNSF Railway?
For a Cut and Shoot quote, send the address or map pin, what will go in the ground, the pipe or conduit size and the footage. A sketch or plans help show whether the route approaches FM 1484, crosses Caney Creek or runs toward Rolling Hills Road. Those details let us review access, nearby utilities and the crossing layout before sizing the work.
The 425 road miles from Yukon are part of mobilization planning for Cut and Shoot. Lilbert loamy fine sand and the mapped clay below it affect drilling and hole support; crossings at FM 1484, Caney Creek or BNSF Railway add planning and exposure needs. Length, pipe size, pavement, pits, excavator time and sand backfill also affect the scope. High profile or emergency work can call for additional planning.
Questions people ask about boring in Cut and Shoot
Does Trinity take directional boring work in Cut and Shoot, Montgomery County?
Yes, we take directional boring work in Cut and Shoot, Montgomery County. Our own crews and satellite yards operated by drilling partners we have vetted can staff the work. You deal with Trinity from the first call through the bore log, whether our crew or a partner crew is on site near FM 1484.
What ground will a Cut and Shoot bore encounter in Lilbert soil?
The USDA soil survey maps Lilbert loamy fine sand across 22 percent of Cut and Shoot. At about 40 inches, loam covers 33 percent of the mapped area and clay 20 percent. Those mapped textures are not test borings; the sandy surface can cave while finer layers may hold the bore open.
Will our directional bore in Cut and Shoot encounter rock below mapped depths?
Although bedrock is not mapped in Cut and Shoot’s top five feet, we consider deeper rock when evaluating bore depth. The geologic map identifies Alluvial pebble gravel and sand of Gelasian age, including unconsolidated gravel, sand, clay and silt. The actual route still needs to be judged from the bore plan and field conditions near Caney Creek.
Who approves a Cut and Shoot bore under FM 1484?
TxDOT reviews a utility owner’s permit application for work in the FM 1484 right of way through the TxDOT Houston District. The utility owner files in RULIS, and we prepare the bore plan and profile for its application. A bore under the existing highway pavement is installed by boring or tunneling.
What will we need for a Cut and Shoot bore under BNSF Railway?
A crossing beneath the BNSF Railway track outside Cut and Shoot requires an agreement with the railroad that owns it. The agreement sets the crossing requirements, including casing, depth and flagging. If the route also occupies highway right of way near FM 1484, TxDOT asks for a copy of that agreement.
Can a line be bored under Caney Creek in Cut and Shoot?
A line can be planned beneath Caney Creek, which runs 1.2 channel miles through Cut and Shoot. The route needs enough depth to stay below the channel, and the crossing is checked for U.S. Army Corps of Engineers jurisdiction during planning. Seasonal water table conditions mapped in the area can also affect the pits.
How far is Cut and Shoot from Yukon, and does Conroe change the job?
Cut and Shoot is 425 road miles from our Yukon, Oklahoma main office, an 8.2 hour drive. Conroe is 8.3 miles west and is the county seat, but it does not change the distance from Yukon. Mobilization is part of planning for work near FM 1484 or Rolling Hills Road.
How much 811 notice does a Cut and Shoot bore near Rolling Hills Road need?
For a bore near Rolling Hills Road, Texas law requires a Texas811 locate request at least 48 hours before excavation, excluding Saturdays, Sundays and legal holidays, and no earlier than 14 days before work. If the start slips more than 14 days past the notice, submit a new request. If marks are worn or moved, we refresh them through Texas811 before continuing work in Cut and Shoot.
What affects the cost of directional boring in Cut and Shoot near FM 1484?
The job scope sets the price for a Cut and Shoot bore. Length, pipe or conduit size, Lilbert soil conditions, pavement, utility crossings, creek work, pits and excavator time all matter. A route under FM 1484 or toward BNSF Railway can add crossing requirements, and the 425 road miles from Yukon affect mobilization.
Where the Cut and Shoot facts on this page come from
- USDA Natural Resources Conservation Service, Soil Data Access: soil survey map units inside Cut and Shoot
- U.S. Census Bureau, TIGER/Line 2024: Cut and Shoot boundary, roads, rail lines and streams
- U.S. Census Bureau, Vintage 2024 population estimates: Cut and Shoot
- U.S. Census Bureau, American Community Survey 2019 to 2023: Cut and Shoot housing units and year built
- Macrostrat geologic map compilation: map units under Cut and Shoot
- U.S. EPA Safe Drinking Water Information System: public water systems serving Cut and Shoot
- U.S. Department of Transportation, North American Rail Network: track owners in Montgomery County
- U.S. Energy Information Administration, Form EIA 861: electric utilities serving Montgomery County
- U.S. Geological Survey, Elevation Point Query Service: Cut and Shoot elevation
- OpenStreetMap road network through the OSRM router: road miles from Yukon, Oklahoma to Cut and Shoot
- Texas Utilities Code Chapter 251, Underground Facility Damage Prevention and Safety
- TxDOT Utility Accommodation Rules, 43 Tex. Admin. Code 21.40: underground utilities
- Texas Department of Transportation: Right of Way Utility and Leasing Information System (RULIS) utility permits
Get a Quote for a Bore in Cut and Shoot
Send the address, what is going in, the size and the footage.
Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com
Free Bore Planner
Plan Your Bore in Cut and Shoot, Texas
Type the address of your job in Cut and Shoot. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.
Talk to the crew that does the work
Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.
Answered by a person, not a call center.
Would rather not call? Send the details and we will come back with a written quote.
County and State Pages for Cut and Shoot
Same county: The Woodlands · Willis · Magnolia · Houston · Pinehurst · Shenandoah · Oak Ridge North · Montgomery · Roman Forest · Splendora · Patton Village · Porter Heights. All counties: Texas county list.
