Trinity Boring Solutions is a full‑service underground utility contractor, not just a drill for rent. We look at the entire route, site constraints and long‑term plans instead of quoting a single bore and leaving others to piece together the rest.

Typical Spencer jobs combine a bore under a road or driveway, trenching along a fence line or property edge and hydro‑vac verification around existing utilities, wells and septic systems.

Because we own the HDD rigs, trenchers and hydro‑vac trucks, we can sequence work efficiently and adjust if soil, weather or access conditions change.

For work that ties into city water or sewer, we encourage owners and contractors to involve us early along with the City of Spencer utility staff or their engineer. We can help review alignments, discuss depths and locate likely conflict points before the project is locked in.

On smaller service jobs we mostly work with the owner and plumber or electrician; on larger projects we coordinate with city staff, inspectors and utility representatives so locates, permits and construction stay aligned.

That upfront coordination reduces last‑minute surprises, redesigns and delays once equipment is on site.

Pricing depends on mobilization, total footage, pipe or conduit size and material, soil conditions, the number and type of crossings, required depths, hydro‑vac needs and restoration. A short residential bore under a driveway is very different from a multi‑utility run across fields and creeks.

Our proposals spell out what is included—bores, trenches, hydro‑vac, backfill and basic restoration—and what remains with others, such as plumbing and electrical tie‑ins, paving, landscaping or specialty traffic control.

When helpful, we also provide options so you can compare an all‑bore route to a combined bore‑and‑trench approach.

We regularly work in Spencer, Nicoma Park, Midwest City, Choctaw, Jones and the wider Oklahoma City metro and will travel anywhere in Oklahoma for the right combination of scope and schedule.

Projects with multiple bores, significant footage or complex crossings are especially good candidates for a statewide mobilization.

For emergencies, response times depend on where crews and equipment are and what is already on the schedule, but we will always give an honest estimate and talk through any immediate safety steps.

Boring is usually the best choice when you need to protect paved roads, long driveways, creeks, established trees, fences, arenas or landscaped areas. It also helps maintain stable cover and separation in soft or erosion‑prone ground.

Trenching is often more economical in open pastures, vacant tracts and construction zones where surfaces are not finished or will be rebuilt anyway.

Many Spencer projects combine bores at crossings with trenches along fence lines or property edges to balance cost, access and restoration.

In an emergency we begin with a quick call to learn what failed, whether utilities or responders are already involved and whether there is any immediate danger. Gas and electric situations must always be cleared by the relevant utility and often by fire or police before we dig.

Once the area is safe and locates are underway, we help the line owner choose between a focused repair and a full reroute, based on access, soil, history of failures and long‑term plans for the property.

Our goal is to end the emergency quickly while improving reliability and access for any future work.

Yes. Acreage owners, farmers, developers and engineers often ask us to review early concepts for homes, shops, barns, arenas and small subdivisions around Spencer. We look at access, grades, likely equipment paths and utility spacing to flag alignments that could be hard or expensive to build or maintain.

We also recommend where to add extra conduits and sleeves while ground is open so future expansions, cameras, gates or equipment can be supported without new excavation.

That field‑driven input helps you avoid avoidable problems and build underground routes that will make sense for decades.

Walk the property and think through where the utility likely starts and ends and what lies between—roads, drives, creeks, fences, corrals, pens, trees or buildings. That quick review makes it easier to explain the site when we talk.

Take photos from the road toward the buildings, from the buildings toward the road and of any tight or complicated areas.

A simple sketch with buildings, fences, key features and a rough route is usually enough to start discussing options and budget ranges.

Many Spencer‑area properties use wells, septic tanks, laterals or lagoons, along with older or undocumented utility lines. We treat those as critical systems to be protected, not obstacles to work around at the last minute.

Hydro‑vac is our primary tool for safely exposing tanks, lines and older pipes, then we adjust bore and trench alignments to keep safe separations and reliable access for future maintenance.

Any maps, notes or even rough history you can share about existing utilities helps us refine that plan further.

Once utilities are buried and surfaces restored, good records are the only dependable way to know where everything runs. We encourage property owners and agencies to capture that information while projects are fresh.

On many Spencer projects we provide simple alignment sketches with depths and key measurements, and on engineered jobs we note any field adjustments so as‑builts match what was actually built.

Those records make future repairs, additions and locates faster, safer and more cost‑effective, and they can add value when properties sell or expand.