trinityboringsolutions.com

Denver City Texas Directional Boring: Patricia Soil, Texas State Highway 83 and Sand Deposits

Quick Answer: The City of Denver City runs the groundwater water system, and electric providers report service in Yoakum County, so we identify the line owner before boring near Texas State Highway 83. Trinity Boring Solutions handles directional boring, also called horizontal directional drilling (HDD), in Denver City, including routes beneath Main Avenue. Denver City is 443 road miles from our Yukon, Oklahoma main office, and that distance affects mobilization for work near Avenue F. Patricia soil and sandy ground call for staged reaming because the hole can cave behind the drill.

Family Business Since 1965 Boring Since 1982 24 Hour Phone No Utility Strike in 25 Years

Denver City bores at a glance

  • Incorporated city in Yoakum County and Gaines County, Texas. Population 4,366 (Census Bureau 2024 estimate).
  • Road distance from our Yukon, Oklahoma main office: 443 miles, about 8.5 hours of driving.
  • Ground: Patricia soil is mapped on 71 percent of the area, with sandy clay loam about 40 inches down.
  • Rock: no bedrock is mapped in the top 60 inches.
  • Highways inside the boundary: Texas State Highway 83, Texas State Highway 214 and FM 2055. State permit office: TxDOT Lubbock District.
  • Railroad track inside the boundary: none mapped.
  • Public water: City of Denver City, groundwater wells.
  • Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
  • Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
  • Phone answered 24 hours a day: (405) 409-7423

Who handles directional boring along Main Avenue in Denver City?

Trinity Boring Solutions takes directional boring work in Denver City after identifying the City of Denver City water system and confirming which electric provider owns the line, a necessary check before a bore along Main Avenue. The Census Bureau Vintage 2024 estimate puts Denver City at 4,366 people. Southwestern Public Service, Lea County Electric Cooperative and Lyntegar Electric Cooperative report electric service in Yoakum County. We install water, sewer, gas, electric conduit and fiber along local streets when the route and utility clearances allow.

Our main office is in Yukon, Oklahoma, and Denver City work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. Our longest bore reached roughly 4,100 feet with 48 inch pipe under the Arkansas River in Tulsa. A Denver City job may instead be a service line or a crossing beneath Texas State Highway 83. Our family business started in 1965, and we have done directional boring since 1982; Denver City is 443 road miles from our Yukon main office.

Ditch Witch JT922 directional drill rig boring beneath an airport taxiway next to a Trinity Boring Solutions truck at Will Rogers World Airport
Our Ditch Witch JT922 boring beneath a taxiway at Will Rogers World Airport in Oklahoma City. Photos on this page are from our jobs in Oklahoma and Texas.

What ground does Patricia soil indicate in Denver City?

The USDA soil survey maps Patricia soil across 71% of Denver City, with sandy surface soils and sandy clay loam common about 40 inches below ground. Patricia and Amarillo loamy fine sands, 0 to 3 percent slopes, cover 64% of the mapped area, while Patricia fine sand covers 8%. At that depth, sandy clay loam is mapped across 81%, and 79% of the area is mapped as sandy. We use Patricia, Arvana, Midessa and Sharvana as mapped soil patterns, not test borings, when planning Denver City bores. Sand can cut easily but may fall back behind the drill, so the hole needs support as it is opened.

USDA soil survey, inside the Denver City city limitsWhat is mapped
Soil series mappedPatricia 71 percent, Arvana 12 percent, Midessa 6 percent, Sharvana 5 percent and Brownfield 3 percent
Texture at the surfaceloamy fine sand 69 percent, fine sandy loam 18 percent and fine sand 11 percent
Texture about 40 inches downsandy clay loam 81 percent, very gravelly loam 12 percent and extremely gravelly sandy loam 5 percent
Engineering class about 40 inches downclayey sand (SC) 74 percent, clayey gravel (GC) 12 percent and lean clay (CL) 7 percent
Average clay content about 40 inches down24 percent
Bedrock mapped within 60 inchesNone mapped
Seasonal water table within 60 inches0 percent of the area
Flood prone soils0 percent of the area
High corrosion risk for uncoated steel0 percent of the area

Bedrock is not mapped in the top five feet of Denver City, which does not rule out rock deeper down. The map includes Cenozoic sedimentary rocks of Paleocene age, as well as Holocene sand sheet deposits. No seasonal water table, flood prone soils or high steel corrosion risk is mapped in the survey area. Sand sheet deposits have moderate to very high permeability and low to moderate water holding capacity, so local sand conditions still matter for keeping the bore open and maintaining fluid returns.

How do we bore Denver City’s sandy clay loam?

Denver City’s sandy clay loam below the surface and loamy fine sand above it call for a supported hole and a controlled reaming sequence. We set the route around the mapped ground and the streets it must pass beneath.

  1. We check the route against Denver City’s Patricia soil and sandy surface mapping, then choose a bore path that fits the proposed line and available access.
  2. Before the drill approaches a marked line near Main Avenue, we hydrovac pothole it; the paint shows location, but not the line’s depth.
  3. In Denver City’s sandy ground, we use drilling fluid to support the hole and ream in stages, with pipe ready before the final pass.
  4. As a bore advances beneath Avenue C or another local street, a walkover locator tracks the drill head and we log depth and pitch.
Bobcat E35 mini excavator lowering a 6 inch PVC sleeve into a bore pit in sandy soil at NE 24th Street in northeast Oklahoma City
Lowering a 6 inch PVC sleeve into a bore pit in sandy soil at NE 24th Street in Oklahoma City.

Which roads and streets can a Denver City bore cross, including Texas State Highway 83?

Texas State Highway 83 and Texas State Highway 214 run through Denver City, along with FM 2055, so a route may need a permitted bore beneath a state road. Main Avenue and Avenue C are each mapped for 1.41 miles inside the city, and Avenue F for 1.35 miles. Avenue D is another long street, at 1.34 miles. Beneath existing highway pavement, TxDOT rules call for boring or tunneling rather than open trenching. Rural highway crossings must extend beneath all travel lanes, and the crossing is encased.

CrossingTypeMapped extentWho has a say
Texas State Highway 83State highway2.5 roadway miles insideState highway office
Texas State Highway 214State highway1.8 roadway miles insideState highway office
FM 2055State highway0.6 roadway miles insideState highway office
Swipe the table sideways to see every column.

No railroad tracks or mapped street and rail crossings are shown inside Denver City, so a rail agreement is not part of a route based on the mapped local network. No streams, lakes or ponds are mapped in or within one mile of the city, and no street crossings of named streams are mapped. That leaves Main Avenue and the state highways as the mapped crossing concerns to check first. If a proposed route reaches a water feature beyond the mapped area, planning checks whether the crossing falls under U.S. Army Corps of Engineers jurisdiction.

Whose approval does a Denver City bore in Yoakum County need?

For a bore under Texas State Highway 83, Texas State Highway 214 or FM 2055 in Denver City, the utility owner applies for the TxDOT utility permit, not the drilling contractor. The TxDOT Lubbock District reviews it through the online RULIS system, and we prepare the bore plan and profile for the owner’s application. The required cover at a highway crossing is 60 inches for water, electric and communication lines, and pressurized sewer lines; along the right of way, electric and communication lines need 48 inches and water needs 36 inches. TxDOT may set a different depth. Denver City is an incorporated town, so we plan Main Avenue bores as work on city streets.

Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.

Who owns the lines near the City of Denver City water system?

The City of Denver City owns the public water system, which draws from groundwater wells and has 2,034 service connections serving 5,500 people. Before a bore near Main Avenue, we confirm which existing water lines are in the route and expose marked utilities before drilling close to them. Southwestern Public Service, Lea County Electric Cooperative and Lyntegar Electric Cooperative report electric service in Yoakum County. The address determines which electric line owner to confirm before conduit work; the county list does not identify a provider for every Denver City address.

Line ownerWhat it isSourceSize
City of Denver CityPublic water systemGroundwater wells2,034 connections, 5,500 people served
Southwestern Public Service, Lea County Electric Cooperative and Lyntegar Electric CooperativeElectric utilities reporting service in Yoakum County and Gaines CountyEIA Form 861Confirm the line owner by address
Swipe the table sideways to see every column.

Denver City’s median housing year is 1973, a detail we keep in mind while verifying utility locations before boring. The survey estimates 29% of homes were built before 1960, 64% from 1960 to 1999 and 7% in 2000 or later. That mix can mean a project is replacing an older service or extending a newer one; the route, not the age estimate, tells us what is underground. On Avenue D or elsewhere, we hydrovac pothole marked utilities on the bore path because locate paint shows position, not depth.

Hydrovac truck and boring equipment staged beside an airport taxiway for utility daylighting in Oklahoma City
Our hydrovac truck and boring equipment beside an airport taxiway in Oklahoma City, set up to expose a utility crossing.

Where is Denver City in relation to Plains?

Denver City is in Yoakum County, with a smaller portion in Gaines County, and Plains is the county seat 15.2 miles north. At an elevation of 3,581 feet, the incorporated town covers 2.61 square miles and uses ZIP code 79323. Seagraves is 15.6 miles east, Seminole is 20.0 miles southeast, Wellman is 24.1 miles east and Loop is 24.5 miles east. Our Yukon yard is 443 road miles away, an 8.5 hour drive, so distance is part of planning mobilization for a Denver City job.

Places near Denver City

What kinds of bores could come up near Main Avenue in Denver City?

  • Highway crossing: A bore beneath Texas State Highway 83 is planned around TxDOT review, the required cover and the full travel lanes.
  • Water service: A connection near the City of Denver City system needs a route checked against existing groundwater well service lines.
  • Fiber route: A fiber bore along Main Avenue can pass beneath pavement without cutting the street surface.
  • Electric conduit: Near Avenue F, we confirm the address specific electric line owner before setting the conduit route.
  • Street service: A water or sewer service crossing Avenue D needs marked utilities exposed along the planned bore path.
  • Airport service: A proposed line near Denver City Airport needs a route and access plan tied to that location.

More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.

What do you need to quote a bore near Avenue D in Denver City?

For an Avenue D quote, send the address or map pin, what will go in the ground, the pipe or conduit size and the footage; a sketch or plans help us read the route. Include the nearest street or crossing, such as Main Avenue or Texas State Highway 83, so we can see where access, pavement and existing lines may affect the bore plan.

The mapped sand and sandy clay loam around Denver City make ground conditions the first detail to check, because the hole may need staged reaming and support. Length and pipe or conduit size also shape the work. A crossing beneath Texas State Highway 83 adds permit and cover planning, while pavement, exposed utilities, pits, excavator time and sand backfill affect the scope. Mobilization matters too: Denver City is 443 road miles from Yukon.

Questions people ask about boring in Denver City

Does Trinity Boring Solutions take directional boring work in Yoakum County and how is a Denver City job staffed?

Yes. We take directional boring work in Denver City and staff it with our own crews or through satellite yards run by partner drilling contractors we have vetted. The Yukon main office remains the point of contact from the first call through the bore log, including for a route near Main Avenue.

What is Patricia soil like for a bore in Denver City?

The USDA soil survey maps Patricia soil across 71% of Denver City, with sandy clay loam mapped across 81% of the area about 40 inches down. Sandy ground can cave behind the drill, so fluid support and staged reaming help keep the hole open. The map describes soil patterns, not a test at a particular address.

Will a Denver City bore hit rock below Avenue F?

Bedrock is not mapped in Denver City’s top five feet, but that does not establish what lies deeper. The geologic map includes Cenozoic sedimentary rocks of Paleocene age and Holocene sand sheet deposits. We use the proposed route and site information to plan; the map alone cannot confirm conditions at an Avenue F bore.

Who approves Denver City bores under Texas State Highway 83 at TxDOT Lubbock District?

The utility owner applies for the permit, and the TxDOT Lubbock District reviews the Texas State Highway 83 crossing through RULIS. We provide the bore plan and profile for that application. Cover depends on the line type, and the TxDOT permit can require a different depth for the Denver City crossing.

Who runs Denver City’s public water system, and does it draw from groundwater wells?

The City of Denver City owns the public water system, and groundwater wells are its source, so we plan utility checks before boring. The system has 2,034 service connections serving 5,500 people. Before a bore near Main Avenue, we check the proposed path against the existing water lines and expose marked utilities before drilling close to them.

Which electric company owns the line for a Denver City conduit bore in Yoakum County?

Southwestern Public Service, Lea County Electric Cooperative and Lyntegar Electric Cooperative report electric service in Yoakum County. That list does not identify the provider at every Denver City address, so confirm the line owner for the route and check conduit specifications with that owner before planning a bore near Avenue D.

Can I reach Trinity after hours for an urgent bore near Avenue F in Denver City?

Yes. For Denver City callers, we answer Trinity’s phone 24 hours a day at (405) 409-7423 to discuss boring plans. For an urgent job near Avenue F, be ready to describe the location, the line to install and any highway or utility crossings so we can understand the Denver City scope.

How much notice does Texas811 need for a Denver City bore near Main Avenue?

Paint near Main Avenue shows a marked line’s position, not its depth. Texas law requires a locate request at least 48 hours before excavation, excluding Saturdays, Sundays and legal holidays, and no earlier than 14 days before work. If the start slips more than 14 days past the notice, submit a new one; worn or moved marks must be refreshed through Texas811 before work continues.

What affects the cost of a Denver City bore beneath Texas State Highway 83?

The price depends on the route and scope, not just footage. Denver City’s sandy ground, pipe or conduit size, bore length, the Texas State Highway 83 crossing, pavement and the number of utilities to expose all affect the work. Pits, excavator time, backfill, emergency needs and mobilization from Yukon can also change the job requirements.

Where the Denver City facts on this page come from

Darren Rice in a safety vest at the bore pit beside the Trinity Boring Solutions Ditch Witch directional drill, with drill rods racked, on the airfield at Will Rogers World Airport in Oklahoma City

About Trinity Boring Solutions

Trinity Boring Solutions is a family business in Yukon, Oklahoma, founded by Dean Rice in 1965 and owned today by Darren Rice, who started its directional boring side in 1982. The company bores across Oklahoma and Texas. No bore is too big or too small: 4 foot sidewalk sleeves to roughly 4,100 feet under the Arkansas River in Tulsa. Reach us at (405) 409-7423.

Get a Quote for a Bore in Denver City

Send the address, what is going in, the size and the footage.

Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com

Trinity Boring Solutions | 24/7 Available ☎ Call (405) 409-7423 Free Quote

Free Bore Planner

Plan Your Bore in Denver City, Texas

Type the address of your job in Denver City. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.

Talk to the crew that does the work

Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.

Call (405) 409-7423

Answered by a person, not a call center.

Would rather not call? Send the details and we will come back with a written quote.

Quick Quote In Page

County and State Pages for Denver City

All counties: Texas county list.