trinityboringsolutions.com

San Elizario Texas Directional Boring: Harkey Loam, FM 258 And River Spur Drain

Quick Answer: At River Spur Drain, Trinity Boring Solutions takes directional boring work in San Elizario, also called horizontal directional drilling (HDD), for routes that need to pass beneath a drain. Our main office in Yukon is 715 road miles away, and FM 258 work is staffed by our own crews or vetted partner crews from satellite yards. Harkey soil is common here, and silty clay loam can cling to a reamer and grip pipe. We adjust the drilling fluid and ream in stages to manage that ground.

Family Business Since 1965 Boring Since 1982 24 Hour Phone No Utility Strike in 25 Years

San Elizario bores at a glance

  • Incorporated city in El Paso County, Texas. Population 10,128 (Census Bureau 2024 estimate).
  • Road distance from our Yukon, Oklahoma main office: 715 miles, about 13.4 hours of driving.
  • Ground: Harkey soil is mapped on 38 percent of the area, with silt loam about 40 inches down.
  • Rock: no bedrock is mapped in the top 60 inches.
  • Highways inside the boundary: FM 258 and FM 1110. State permit office: TxDOT El Paso District.
  • Railroad track inside the boundary: none mapped.
  • Named streams inside the boundary: River Spur Drain, San Elizario Lateral, River Intercepting Drain and San Elizarjo Lateral.
  • Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
  • Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
  • Phone answered 24 hours a day: (405) 409-7423

Who can handle directional boring near River Spur Drain in San Elizario?

Trinity Boring Solutions takes directional boring work in San Elizario, El Paso County, where the Census Bureau Vintage 2024 estimate puts the population at 10,128. Along Socorro Road or Cuadrilla Road, our crews can install water, sewer, gas, electric conduit or fiber without opening the full street. We size the bore to the line and crossing.

Our main office is in Yukon, Oklahoma, and San Elizario work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. We have had no utility strike in over 25 years, and our family business began in 1965, with directional boring since 1982. That record matters around buried lines in El Paso County, where El Paso Electric and Rio Grande Electric Cooperative report electric service.

Trinity Boring Solutions Vermeer D24x40 directional drill set up for a bore
Our Vermeer D24x40 directional drill set up for a bore. Photos on this page are from our jobs in Oklahoma and Texas.

What does the soil survey show about Harkey soil in San Elizario?

The USDA soil survey maps Harkey across 38 percent of San Elizario, including Harkey silty clay loam and Harkey loam map units at 19 percent each. About 40 inches down, silt loam accounts for 28 percent of mapped ground, while loamy fine sand accounts for 12 percent. The surface texture is silty clay loam across 44 percent of the city, and 23 percent is mapped as sandy at that depth. These are mapped soil patterns, not test borings, so a route near FM 258 still needs site specific planning.

USDA soil survey, inside the San Elizario city limitsWhat is mapped
Soil series mappedHarkey 38 percent, Glendale 22 percent, Gila 9 percent, Tigua 8 percent and Saneli 8 percent
Texture at the surfacesilty clay loam 44 percent, loam 25 percent and silty clay 19 percent
Texture about 40 inches downsilt loam 28 percent, stratified fine sand to silty clay loam 21 percent and loam 19 percent
Engineering class about 40 inches downsilt (ML) 47 percent, silty sand (SM) 34 percent and sand with silt (SP SM) 8 percent
Average clay content about 40 inches down19 percent
Bedrock mapped within 60 inchesNone mapped
Seasonal water table within 60 inches0 percent of the area
Flood prone soils0 percent of the area
High corrosion risk for uncoated steel45 percent of the area

Bedrock is not mapped in the top five feet of San Elizario, which does not rule out deeper rock. The USDA soil survey maps no seasonal water table within 60 inches and no flood prone soils, but River Spur Drain still needs a crossing plan. High steel corrosion risk covers 45 percent of the mapped area, so the line owner should choose any casing or tracer wire coating; HDPE avoids that soil corrosion concern. The geologic map shows Holocene Alluvium of sand, silt, clay and gravel, so ground can vary along a bore.

How do crews handle silt loam and Harkey soil in San Elizario?

San Elizario has silty clay loam at the surface and mapped silt loam about 40 inches down. We match the fluid and reaming approach to the ground along each route, including near River Spur Drain.

  1. In Harkey silty clay loam, we use a thinner drilling fluid and staged reaming to limit sticky buildup, then plan to pull pipe the day the hole opens.
  2. Where the survey maps silt loam at about 40 inches, we keep fluid pressure low near pavement so soft ground does not wash out under FM 258.
  3. In the mapped fine sand to silty clay loam layers near River Spur Drain, we build a stable bore wall and have the pipe ready before the final ream.
  4. Before approaching marked lines along Socorro Road, we hydrovac pothole each utility on the path; a surface mark gives position, not depth.
6 inch Schedule 40 PVC sleeve in a bore pit in sandy soil on a water main crossing at NE 24th Street, Oklahoma City
A 6 inch Schedule 40 PVC sleeve in a bore pit in sandy soil on a water main crossing in Oklahoma City.

Where might a line go under FM 258 in San Elizario?

FM 258 has 4.3 mapped roadway miles inside San Elizario, and FM 1110 has 0.6. Texas State Highway 20 is 0.3 miles outside the city limits, so a nearby route may also need state right of way planning. Socorro Road runs 4.79 miles in the city, Cuadrilla Road 4.28 miles and Chicken Ranch Road 2.07 miles. A bore can pass beneath pavement instead of cutting across those streets, with the path and pits planned around access and existing lines.

CrossingTypeMapped extentWho has a say
FM 258State highway4.3 roadway miles insideState highway office
FM 1110State highway0.6 roadway miles insideState highway office
Texas State Highway 20Highway nearby0.3 miles outsideState highway office
Union PacificRailroad nearby0.7 miles outsideThe railroad
River Spur DrainStream2.47 channel miles insideChecked for Corps of Engineers jurisdiction
San Elizario LateralStream1.9 channel miles insideChecked for Corps of Engineers jurisdiction
River Intercepting DrainStream1.59 channel miles insideChecked for Corps of Engineers jurisdiction
San Elizarjo LateralStream1.52 channel miles insideChecked for Corps of Engineers jurisdiction
Bernal LateralStream1.38 channel miles insideChecked for Corps of Engineers jurisdiction
Río GrandeStream1.1 channel miles insideChecked for Corps of Engineers jurisdiction
Canas Agrias LateralStream1.04 channel miles insideChecked for Corps of Engineers jurisdiction
Barrial LateralStream1 channel miles insideChecked for Corps of Engineers jurisdiction
Island Main LateralStream nearbyAlong the boundaryChecked for Corps of Engineers jurisdiction
Franklin CanalStream nearbyAlong the boundaryChecked for Corps of Engineers jurisdiction
Swipe the table sideways to see every column.

No railroad is mapped inside San Elizario, and none of its mapped street and rail crossings are identified; a Union Pacific track is 0.7 miles outside the limits. Named streams include River Spur Drain at 2.47 channel miles and San Elizario Lateral at 1.9. The city has 33 mapped street crossings of named streams, so a route near a lateral or drain needs careful crossing layout. For boring in San Elizario, we have no lakes or ponds mapped within one mile to flag as crossings.

Who approves Union Pacific or highway work in San Elizario?

At FM 258 and FM 1110, TxDOT cover requirements help set bore depth: electric and communication crossings need 60 inches below the lowest crossed grade, while water crossings need 60 inches and pressurized sewer crossings need 60 inches. For lines along highway right of way, cover is 48 inches for electric and communications and 36 inches for water. The line owner files a utility permit through TxDOT RULIS, reviewed by the TxDOT El Paso District; we provide the bore plan and profile. Existing highway crossings are bored or tunneled and encased. A Union Pacific crossing needs that railroad’s agreement, and River Spur Drain is checked for federal waterway jurisdiction during planning.

Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.

Who owns the lines in San Elizario and El Paso County?

EPA drinking water records do not let us match a public water provider to a specific San Elizario address. Before planning a bore near Socorro Road, confirm the address provider with the city, El Paso County or the local water district. El Paso Electric and Rio Grande Electric Cooperative report electric service in the county, but that does not identify the owner of every line. We confirm the line owner before planning an electric conduit bore near FM 258.

Line ownerWhat it isSourceSize
El Paso Electric and Rio Grande Electric CooperativeElectric utilities reporting service in El Paso CountyEIA Form 861Confirm the line owner by address
Swipe the table sideways to see every column.

The American Community Survey 2019 to 2023 five year estimates put San Elizario’s median housing year at 2003; 4 percent of homes were built before 1960 and 57 percent in 2000 or later. Along Cuadrilla Road, a replacement bore and a new service may meet different buried lines, so the address and route matter. We hydrovac pothole marked utilities on the bore path before drilling near them, because paint shows position, not depth.

Hydrovac truck and boring equipment staged beside an airport taxiway for utility daylighting in Oklahoma City
Our hydrovac truck and boring equipment beside an airport taxiway in Oklahoma City, set up to expose a utility crossing.

Where is San Elizario in relation to Clint and Socorro?

San Elizario is an incorporated city in El Paso County, with 6.9 square miles of land and an elevation of 3,636 feet. Its ZIP code is 79849. Clint is 2.1 miles east, Morning Glory is 3.3 miles east and Socorro is 4.2 miles north. El Paso, the county seat, is 21.1 miles northwest. Our Yukon, Oklahoma main office is 715 road miles away, a 13.4 hour drive, so distance can affect crew mobilization for a bore near FM 258.

Places near San Elizario

What would we bore near Socorro Road in San Elizario?

  • Highway crossing: A bore beneath FM 258 can avoid cutting its pavement, with depth and access planned for the TxDOT right of way.
  • Street service: A water or sewer service along Socorro Road can be bored beneath the street surface, with pits placed outside the crossing.
  • Fiber route: A conduit bore along Cuadrilla Road can carry fiber while avoiding an open cut across the street.
  • Drain crossing: A route beneath River Spur Drain needs a planned path that accounts for the channel and checks jurisdiction during planning.
  • Rail crossing: A route toward the Union Pacific track 0.7 miles outside the city limits needs the railroad’s crossing agreement.
  • Electric conduit: Near Chicken Ranch Road, we first confirm the line owner and expose marked utilities along the proposed bore path.

More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.

What do you need to quote a bore near Thompson Road in San Elizario?

For a Thompson Road quote, send the address or map pin, what will go in the ground, pipe or conduit size and footage; a sketch or plans help. Tell us if the route reaches FM 258 or River Spur Drain. Those details show where we need to plan pits, check access and look for marked utilities before setting the bore path.

Harkey soil and the changing alluvium matter first because clay can grip pipe while sand can cave behind the bit. The number of utilities to expose, pipe size and footage also shape the work. An FM 258 crossing adds highway planning, while a River Spur Drain route may need water crossing review. Pavement, pits, excavator time and backfill affect the scope, as does mobilization from Yukon, 715 road miles away.

Questions people ask about boring in San Elizario

Does Trinity take directional boring work in San Elizario and El Paso County, and who staffs it?

Yes. We take directional boring work in San Elizario, and the customer works with Trinity from the first call through the bore log. Our own crews and vetted partner drilling contractors operating satellite yards can staff work near Socorro Road. Trinity serves Oklahoma and Texas and also takes work in nearby states.

Who is responsible for Chicken Ranch Road in San Elizario, and does a bore require cutting it?

Because San Elizario is incorporated, we treat its city streets as belonging to the city when planning boring access. A directional bore beneath Chicken Ranch Road can avoid cutting the full street, with entry and exit pits set in suitable locations. The route still needs to account for marked utilities and any pavement or access constraints.

How old are homes and buried lines near Cuadrilla Road in San Elizario?

The American Community Survey 2019 to 2023 five year estimates give San Elizario a median housing year of 2003, with 4 percent of homes built before 1960. That does not date the buried lines along Cuadrilla Road. For a replacement bore, we expose marked utilities first and plan around what is found along the proposed path.

Can Harkey soil in San Elizario corrode steel, and what pipe should I use?

The USDA soil survey maps high steel corrosion risk across 45 percent of San Elizario, including areas mapped as Harkey soil. That is a planning concern for steel casing or tracer wire, not a pipe selection rule. The line owner chooses any protective coating; HDPE is not affected by that soil corrosion concern.

What ground will a bore pass through in Harkey soil in San Elizario?

The USDA soil survey maps Harkey across 38 percent of San Elizario. At about 40 inches, silt loam covers 28 percent of the mapped area, with fine sand to silty clay loam also represented. Those mapped patterns help plan a bore, but conditions can vary along a route near FM 258.

Could our bore in San Elizario encounter rock at greater drilling depth?

In San Elizario, we do not see bedrock mapped in the top five feet, though deeper rock may still affect boring depth. The geologic map shows Holocene Alluvium made up of sand, silt, clay and gravel. Near River Spur Drain, that range of materials can mean the drilling approach needs to match the ground found along the route.

Does Trinity serve Clint and rural sites outside San Elizario?

We take work across Texas, including projects outside incorporated limits, and can discuss a site near Clint, 2.1 miles east of San Elizario. The address and proposed route help us assess access, utility crossings and distance from the Yukon main office. The actual line owner and water provider must be confirmed for the address.

How much notice does Texas811 need for a bore near Socorro Road in San Elizario?

For a bore along Socorro Road, request locates at least 48 hours before excavation, not counting Saturdays, Sundays or legal holidays, and no earlier than 14 days before work. If our San Elizario start slips more than 14 days past the original notice, we submit a new request before work proceeds. Before work continues in San Elizario, we ask that worn or moved marks be refreshed through Texas811.

What affects the cost of directional boring near FM 258 in San Elizario when we plan the crossing route and installation depth?

The price depends on the route and scope, not just footage. Harkey soil and alluvial ground affect drilling, while an FM 258 crossing can add highway planning. Pipe size, length, marked utilities to expose, pavement, pits, creek or drain crossings, backfill and mobilization from Yukon all affect the estimate.

Where the San Elizario facts on this page come from

Darren Rice in a safety vest at the bore pit beside the Trinity Boring Solutions Ditch Witch directional drill, with drill rods racked, on the airfield at Will Rogers World Airport in Oklahoma City

About Trinity Boring Solutions

Trinity Boring Solutions is a family business in Yukon, Oklahoma, founded by Dean Rice in 1965 and owned today by Darren Rice, who started its directional boring side in 1982. The company bores across Oklahoma and Texas. No bore is too big or too small: 4 foot sidewalk sleeves to roughly 4,100 feet under the Arkansas River in Tulsa. Reach us at (405) 409-7423.

Get a Quote for a Bore in San Elizario

Send the address, what is going in, the size and the footage.

Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com

Trinity Boring Solutions | 24/7 Available ☎ Call (405) 409-7423 Free Quote

Free Bore Planner

Plan Your Bore in San Elizario, Texas

Type the address of your job in San Elizario. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.

Talk to the crew that does the work

Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.

Call (405) 409-7423

Answered by a person, not a call center.

Would rather not call? Send the details and we will come back with a written quote.

Quick Quote In Page

County and State Pages for San Elizario

Same county: El Paso · Fort Bliss · Fabens · Homestead Meadows South · Canutillo · Homestead Meadows North · Anthony · Westway · Agua Dulce · Vinton · Tornillo · Prado Verde. All counties: Texas county list.