Hornsby Bend Texas Directional Boring: Bergstrom Soil, FM 969 and Elm Creek
Quick Answer: We handle directional boring, also called horizontal directional drilling (HDD), for crossings of FM 969 and other Hornsby Bend routes. Our Yukon, Oklahoma office is 404 road miles away, and that distance matters for work near Elm Creek. The USDA soil survey maps Bergstrom soil across much of Hornsby Bend. Clay can hold a bore open, but it can also stick to the reamer and grip the pipe.
Hornsby Bend bores at a glance
- Unincorporated community in Travis County, Texas. Population 12,168 (2020 Census count).
- Road distance from our Yukon, Oklahoma main office: 404 miles, about 7.7 hours of driving.
- Ground: Bergstrom soil is mapped on 31 percent of the area, with silt loam about 40 inches down.
- Rock: bedrock is mapped within 60 inches on 3 percent of the area.
- Highways inside the boundary: FM 969 and Texas State Highway 130. State permit office: TxDOT Austin District.
- Railroad track inside the boundary: none mapped.
- Named streams inside the boundary: Elm Creek, Decker Creek and Colorado River.
- Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
- Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
- Phone answered 24 hours a day: (405) 409-7423
Who handles directional boring near Elm Creek in Hornsby Bend?
Trinity Boring Solutions takes directional boring work in Hornsby Bend, an unincorporated community in Travis County where Elm Creek runs through the mapped area. The Census Bureau counted 12,168 residents in 2020; it does not publish yearly estimates for unincorporated places. We install water, sewer, gas, electric conduit and fiber lines, including routes beneath local streets or across Elm Creek.
Our main office is in Yukon, Oklahoma, and Hornsby Bend work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. For a short service line near Gilbert Road or a larger casing project near FM 969, our equipment handles sizes from 3/4 inch to 48 inch casing and lengths from 10 feet to 5,000 feet. In Travis County, our family business began in 1965, and we have performed directional boring since 1982.

What does the Bergstrom soil survey show in Hornsby Bend?
The USDA soil survey maps Bergstrom as the leading soil series in Hornsby Bend, covering 31 percent of the area. Bergstrom silty clay loam is mapped on 17 percent, and Bergstrom silt loam on 7 percent. About 40 inches down, silt loam is mapped under 24 percent of the area, while clay is mapped under 24 percent. The survey also maps an average clay content of 33 percent at that depth. These are mapped patterns, not test borings, so the exact ground along Dunlap Road still needs site specific planning.
| USDA soil survey, inside the Hornsby Bend mapped community boundary | What is mapped |
|---|---|
| Soil series mapped | Bergstrom 31 percent, Yahola 13 percent, Heaton 8 percent, Travis 8 percent and Tinn 6 percent |
| Texture at the surface | silty clay loam 26 percent, clay 19 percent and silt loam 10 percent |
| Texture about 40 inches down | silt loam 24 percent, clay 24 percent and fine sandy loam 13 percent |
| Engineering class about 40 inches down | lean clay (CL) 43 percent, fat clay (CH) 27 percent and silty clay (CL ML) 13 percent |
| Average clay content about 40 inches down | 33 percent |
| Bedrock mapped within 60 inches | 3 percent of the area (0 percent hard rock, 3 percent weathered rock) |
| Seasonal water table within 60 inches | 2 percent of the area |
| Flood prone soils | 27 percent of the area |
| High corrosion risk for uncoated steel | 32 percent of the area |
Bedrock is mapped within 60 inches in 3 percent of Hornsby Bend, with a typical mapped depth of 36 inches; that calls for checking the route rather than assuming soil all the way down. Seasonal water tables within 60 inches cover 2 percent, while flood prone soils cover 27 percent, a concern near Elm Creek. High steel corrosion risk is mapped on 32 percent. The USDA geology map includes Pleistocene alluvium of clay, silt, sand and gravel, plus Late Cretaceous sand, chalk and mud. Clay can ball on a reamer, and creek ground needs depth planning.
How do we bore silt loam and clay in Hornsby Bend?
The USDA soil survey maps silt loam and clay in Hornsby Bend, so we adjust drilling fluid and reaming to the ground along each route. Near Elm Creek, we also plan depth around channel conditions.
- Bergstrom clay can hold the hole but stick to the reamer, so we use suitable fluid and staged reaming before pulling pipe near Gilbert Road.
- Where Hornsby Bend silt loam is present, we limit fluid pressure under pavement because wet, soft ground can weaken steering.
- In mapped alluvial sand and gravel near Elm Creek, we plan to keep the hole supported and have the pipe ready before the final ream.
- We expose marked utilities on a route near FM 969 with hydrovac potholing, then track the drill head and record depth and pitch.

Where might a line go under FM 969 in Hornsby Bend?
A bore beneath FM 969 or Texas State Highway 130 in Hornsby Bend needs a route and depth suited to the state highway crossing. FM 969 has 2.7 mapped roadway miles inside the community boundary, and Highway 130 has 1.3. Dunlap Road is the longest named street at 2.96 miles, followed by Webberville Road at 2.68 miles and Gilbert Road at 2.44 miles. Texas State Highway 71 lies 0.9 miles outside the boundary. These streets and highways give a project its actual crossing points and access needs.
| Crossing | Type | Mapped extent | Who has a say |
|---|---|---|---|
| FM 969 | State highway | 2.7 roadway miles inside | State highway office |
| Texas State Highway 130 | State highway | 1.3 roadway miles inside | State highway office |
| Texas State Highway 71 | Highway nearby | 0.9 miles outside | State highway office |
| Elm Creek | Stream | 5.8 channel miles inside | Checked for Corps of Engineers jurisdiction |
| Decker Creek | Stream | 1.06 channel miles inside | Checked for Corps of Engineers jurisdiction |
| Colorado River | Stream | 0.78 channel miles inside | Checked for Corps of Engineers jurisdiction |
| Onion Creek | Stream nearby | Along the boundary | Checked for Corps of Engineers jurisdiction |
| Gilleland Creek | Stream nearby | 0.6 miles outside | Checked for Corps of Engineers jurisdiction |
| Elk Creek | Stream nearby | 0.6 miles outside | Checked for Corps of Engineers jurisdiction |
| Walter East Long Lake | Lake or pond | 1,260 acres, nearby | Checked for Corps of Engineers jurisdiction |
No railroad is mapped inside Hornsby Bend or within one mile outside the community boundary, so a rail agreement is not part of the mapped local crossing picture. Elm Creek runs 5.8 channel miles inside the area; Decker Creek and the Colorado River are also mapped. Public records map six street crossings of named streams, but do not identify their locations. Creek and river routes need review for Corps jurisdiction during planning. Walter East Long Lake is nearby, outside the boundary.
Who approves a bore in Travis County near FM 969 in Hornsby Bend?
Hornsby Bend has no city government, so a street bore is not permitted by a local city office; the responsible county or state authority depends on the route. FM 969 and Texas State Highway 130 are state highways, so a utility crossing their right of way needs a TxDOT utility permit. The utility owner files through TxDOT RULIS, and the TxDOT Austin District reviews it; we prepare the bore plan and profile for the owner’s application. For electric or communication lines crossing a highway, the stated cover is at least 60 inches below the lowest crossed grade, with 48 inches along the right of way. Creek crossings such as Elm Creek are checked for Corps jurisdiction.
Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.
What lines should crews check in Travis County near Elm Creek in Hornsby Bend?
The water provider for a specific Hornsby Bend address has to be confirmed with the city, the county or the local water district before a bore is planned. That check matters before a route near Elm Creek is set. Utilities reporting electric service in Travis County include Oncor Electric Delivery Company, Austin Energy, Bluebonnet Electric Cooperative and Pedernales Electric Cooperative. We confirm the owner for the particular line before planning an electric conduit bore, since the countywide list does not identify the provider at every address.
| Line owner | What it is | Source | Size |
|---|---|---|---|
| Oncor Electric Delivery Company, Austin Energy, Bluebonnet Electric Cooperative and Pedernales Electric Cooperative | Electric utilities reporting service in Travis County | EIA Form 861 | Confirm the line owner by address |
The American Community Survey 2019 to 2023 estimates put Hornsby Bend’s median housing year at 2010; 1 percent of homes were built before 1960 and 81 percent in 2000 or later. Near Webberville Road, that mix can mean either a replacement route or a new service, not a reliable age estimate for buried lines. Before drilling close to a marked line, we use hydrovac potholing to expose it. That is especially useful where a proposed water route approaches electric conduit.

What is near Hornsby Bend and Garfield?
Hornsby Bend is in Travis County, southeast of Austin, at an elevation of 440 feet across 9.4 square miles. The community uses ZIP codes 78725 and 78724. Garfield is 3.1 miles southeast, Webberville is 5.5 miles east, and Manor is 8.1 miles north. Austin, the county seat and nearest larger city, is 10.6 miles northwest. From our Yukon yard, the drive to Hornsby Bend is 404 road miles and 7.7 hours. That distance is part of planning a job near FM 969.
Places near Hornsby Bend
- Directional boring in Garfield: 3.1 miles southeast
- Webberville: 5.5 miles east
- Directional boring in Manor: 8.1 miles north
- Directional boring in Wyldwood: 10.2 miles southeast
- Directional boring in Austin: 10.6 miles northwest
What would we bore near Elm Creek in Hornsby Bend?
- Highway crossing: A route under FM 969 needs a bore plan that accounts for TxDOT cover requirements and the highway right of way.
- Street service: A water or sewer line beneath Dunlap Road can avoid an open cut across pavement when the route and pits allow it.
- Creek crossing: A line beneath Elm Creek needs depth planning around the channel and a check for Corps jurisdiction during planning.
- Electric conduit: Near Webberville Road, we confirm the line owner and expose marked utilities before drilling close to them.
- Fiber route: A fiber bore along Gilbert Road can connect service without cutting the street, with the route checked for existing lines.
- Water service: A proposed service near Decker Creek starts with confirming the provider for that Hornsby Bend address.
More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.
What drives the price of a bore near Dunlap Road in Hornsby Bend?
A map pin near Dunlap Road or Elm Creek shows the exact route, which matters for checking street, drainage and utility crossings in Hornsby Bend. For work involving Dunlap Road, we need to know what goes in the ground, the pipe or conduit size, and footage. A sketch or plans help us understand the pits, access and route before we scope the work.
Mobilization starts with the 404 road miles from Yukon, then the Hornsby Bend ground and route shape the rest. Bergstrom clay can affect reaming and fluid, while an FM 969 crossing brings a state permit and cover requirements. We also account for length, pipe size, exposed utilities, pavement, creek crossings, pits, excavator time and sand backfill. A route near Elm Creek or Dunlap Road can have different crossing and access needs from a service line in open ground.
Questions people ask about boring in Hornsby Bend
Does Trinity Boring Solutions take directional boring work in Hornsby Bend, Travis County, and how is it staffed?
Yes. We take work in Hornsby Bend, and our Yukon office coordinates with our own crews and vetted drilling partners rather than a local office. The same Trinity contact stays involved from the first call through the bore log, including jobs along FM 969.
Can you bore a line under Elm Creek in Hornsby Bend?
A bore under Elm Creek can be planned, subject to the route, ground and required review. The creek has 5.8 channel miles inside Hornsby Bend, and creek crossings are checked for Corps jurisdiction during planning. We need the proposed crossing location to assess depth and access.
Who owns electric lines in Hornsby Bend, Travis County, and who confirms conduit specifications?
The owner depends on the address. Oncor Electric Delivery Company, Austin Energy, Bluebonnet Electric Cooperative and Pedernales Electric Cooperative report service in Travis County. We confirm the specific line owner before planning conduit near a route such as Gilbert Road, and the owner supplies the applicable requirements.
Does Travis County or a city control Gilbert Road in Hornsby Bend, and must it be cut?
Hornsby Bend is unincorporated and has no city government, so the county or state authority is responsible depending on the road. A bore can pass below Gilbert Road without cutting pavement when the route works; the road’s mapped length is 2.44 miles inside the community.
How old are homes and buried lines near Webberville Road in Hornsby Bend, and can replacement lines be bored?
Homes have a median build year of 2010 in the American Community Survey 2019 to 2023 estimates, but that does not establish the age of buried lines near Webberville Road. We can plan a replacement bore after checking the route and exposing marked utilities before drilling nearby.
Could groundwater or flood prone ground affect bore pits near Elm Creek in Hornsby Bend?
It could. The USDA soil survey maps flood prone soils across 27 percent of Hornsby Bend and seasonal water tables within 60 inches across 2 percent. Near Elm Creek, we plan pit placement and depth for the site, and pumping may be needed if a pit fills with water.
How much notice does Texas811 need for a Hornsby Bend bore near Dunlap Road, and what if marks change?
For a bore near Dunlap Road, request the locate at least 48 hours before excavation, excluding Saturdays, Sundays and legal holidays, and no earlier than 14 days ahead. If our start slips more than 14 days past the original notice for a Decker Creek crossing, we will submit a new request. Refresh marks through Texas811 if they wear off or move.
How far is Hornsby Bend from Trinity’s Yukon office, and does the Austin area distance affect a job?
Hornsby Bend is 404 road miles and a 7.7 hour drive from our Yukon yard, with Austin 10.6 miles northwest. The long mobilization can affect the job plan, along with local conditions such as an FM 969 crossing, Elm Creek access or Bergstrom clay.
What affects our directional boring costs in Bergstrom soil near FM 969, Hornsby Bend?
The scope determines the price: route length, pipe size, Bergstrom soil, utility exposures, pavement and creek crossings all matter. An FM 969 crossing adds state right of way planning, while mobilization reflects the 404 road miles from Yukon. Pits, excavator time, backfill and emergency timing can also change the work involved.
Where the Hornsby Bend facts on this page come from
- USDA Natural Resources Conservation Service, Soil Data Access: soil survey map units inside Hornsby Bend
- U.S. Census Bureau, TIGER/Line 2024: Hornsby Bend boundary, roads, rail lines and streams
- U.S. Census Bureau, 2020 Census: Hornsby Bend population count
- U.S. Census Bureau, American Community Survey 2019 to 2023: Hornsby Bend housing units and year built
- Macrostrat geologic map compilation: map units under Hornsby Bend
- U.S. Energy Information Administration, Form EIA 861: electric utilities serving Travis County
- U.S. Geological Survey, Elevation Point Query Service: Hornsby Bend elevation
- OpenStreetMap road network through the OSRM router: road miles from Yukon, Oklahoma to Hornsby Bend
- Texas Utilities Code Chapter 251, Underground Facility Damage Prevention and Safety
- TxDOT Utility Accommodation Rules, 43 Tex. Admin. Code 21.40: underground utilities
- Texas Department of Transportation: Right of Way Utility and Leasing Information System (RULIS) utility permits
Get a Quote for a Bore in Hornsby Bend
Send the address, what is going in, the size and the footage.
Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com
Free Bore Planner
Plan Your Bore in Hornsby Bend, Texas
Type the address of your job in Hornsby Bend. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.
Talk to the crew that does the work
Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.
Answered by a person, not a call center.
Would rather not call? Send the details and we will come back with a written quote.
County and State Pages for Hornsby Bend
Same county: Pflugerville · Lakeway · Leander · Wells Branch · Lago Vista · Bee Cave · Cedar Park · Shady Hollow · West Lake Hills · Barton Creek · Hudson Bend · Jonestown. All counties: Texas county list.
