Eidson Road Texas Directional Boring: Lagloria Soil, Loop 480 and Union Pacific
Quick Answer: AEP Texas Central and Rio Grande Electric Cooperative report electric service in Maverick County, while the water provider needs address level confirmation before a Loop 480 bore. We take directional boring, also called horizontal directional drilling (HDD), in Eidson Road for routes beneath Loop 480 without cutting pavement. The Yukon, Oklahoma main office is 596 road miles from Eidson Road, so distance affects mobilization for work near Canal Road or Union Pacific track. Lagloria soil and very fine sandy loam dominate the mapped ground, so we plan the drilling fluid and reaming around the route rather than assume one soil condition throughout.
Eidson Road bores at a glance
- Unincorporated community in Maverick County, Texas. Population 9,461 (2020 Census count).
- Road distance from our Yukon, Oklahoma main office: 596 miles, about 11.9 hours of driving.
- Ground: Lagloria soil is mapped on 46 percent of the area, with very fine sandy loam about 40 inches down.
- Rock: bedrock is mapped within 60 inches on 16 percent of the area.
- Highways inside the boundary: Loop 480. State permit office: TxDOT Laredo District.
- Railroad track inside the boundary: Union Pacific, with 2 mapped street and rail crossings.
- Named streams inside the boundary: Maverick County Water Ditch.
- Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
- Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
- Phone answered 24 hours a day: (405) 409-7423
Does anyone provide directional boring in Eidson Road near Union Pacific?
Trinity Boring Solutions takes directional boring work in Eidson Road, where the water provider must be confirmed for the address and AEP Texas Central and Rio Grande Electric Cooperative report electric service in Maverick County. The Census Bureau counted 9,461 residents in 2020. We install water, sewer, gas, electric conduit and fiber on routes such as Eidson Road and Canal Road, with the line owner identified before planning a conduit bore.
Our main office is in Yukon, Oklahoma, and Eidson Road work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. Our longest bore ran roughly 4,100 feet with 48 inch pipe under the Arkansas River in Tulsa. A typical Eidson Road job is smaller, but Loop 480 and the Union Pacific track still call for route specific planning. We have been a family business since 1965 and have done directional boring since 1982.

How does Lagloria soil affect drilling in Eidson Road?
The USDA soil survey maps Lagloria across 46 percent of Eidson Road, with very fine sandy loam mapped at about 40 inches across 46 percent of the area. Very fine sandy loam is the leading surface texture, covering 55 percent, while silty clay loam covers 15 percent and clay covers 9 percent. These are mapped patterns, not test borings, so a Canal Road route may differ from the area wide pattern. We use the site plan and field conditions to choose fluid and reaming steps.
| USDA soil survey, inside the Eidson Road mapped community boundary | What is mapped |
|---|---|
| Soil series mapped | Lagloria 46 percent, Elindio 11 percent, Copita 9 percent, Rio Grande 8 percent and Montell 6 percent |
| Texture at the surface | very fine sandy loam 55 percent, silty clay loam 15 percent and clay 9 percent |
| Texture about 40 inches down | very fine sandy loam 46 percent, clay loam 11 percent and cemented bedrock 10 percent |
| Engineering class about 40 inches down | silty clay (CL ML) 46 percent, lean clay (CL) 23 percent and fat clay (CH) 9 percent |
| Average clay content about 40 inches down | 21 percent |
| Bedrock mapped within 60 inches | 16 percent of the area (0 percent hard rock, 16 percent weathered rock) |
| Seasonal water table within 60 inches | 0 percent of the area |
| Flood prone soils | 8 percent of the area |
| High corrosion risk for uncoated steel | 84 percent of the area |
At about 40 inches, the survey maps an average clay content of 21 percent, and 20 percent of the area has heavy clay. Clay can stick to a reamer, so staged reaming and fluid suited to the ground help manage the hole. Bedrock is mapped within five feet in 16 percent of the area, all as weathered bedrock; hard bedrock is not mapped there. Seasonal water tables are not mapped, while flood prone soils cover 8 percent. High steel corrosion risk covers 84 percent, so the line owner should consider casing and tracer wire materials. The Escondito Formation, of Late Cretaceous age, includes clay, sandstone, siltstone and limestone.
How do we drill Eidson Road’s very fine sandy loam?
The USDA soil survey maps very fine sandy loam across 55 percent of Eidson Road, but the route may also meet clay or weathered bedrock. We adjust the bore plan to the ground found along the specific street or crossing.
- Lagloria soil and the mapped clay share can make cuttings cling to the reamer, so we use staged reaming and fluid suited to the route.
- Where the Eidson Road route meets very fine sandy loam, we watch fluid returns and keep the pull pipe ready as the hole is opened.
- The survey maps weathered bedrock in 16 percent of the area; if encountered, a soil bit can work, but progress may be slower than in soil.
- Near Loop 480 pavement, we control fluid pressure and track the drill head from the surface, recording depth and pitch as the bore advances.

Which roads, tracks or creeks can a bore cross in Eidson Road near Loop 480?
Loop 480 is the state highway mapped inside Eidson Road, with 4.4 roadway miles in the community boundary. US 57 is 0.6 miles outside it, US 277 Business is 1.0 mile away, and US 277 is 1.4 miles away. Eidson Road is the longest named street at 2.09 miles, followed by Canal Road at 1.28 miles and Venesa Street at 0.91 miles. A bore route under one of these roads needs its own depth, access and utility review.
| Crossing | Type | Mapped extent | Who has a say |
|---|---|---|---|
| Loop 480 | State highway | 4.4 roadway miles inside | State highway office |
| US 57 | Highway nearby | 0.6 miles outside | State highway office |
| US 277 Business | Highway nearby | 1 miles outside | State highway office |
| US 277 | Highway nearby | 1.4 miles outside | State highway office |
| Union Pacific | Railroad | 0.33 track miles inside | The railroad |
| Maverick County Water Ditch | Stream | 0.31 channel miles inside | Checked for Corps of Engineers jurisdiction |
| Maverick County Canal | Stream nearby | 0.7 miles outside | Checked for Corps of Engineers jurisdiction |
Union Pacific has 0.33 track miles inside Eidson Road, and public mapping shows 2 street and rail crossings in the community. A crossing of that track needs an agreement from Union Pacific covering the crossing conditions. Maverick County Water Ditch runs 0.31 channel miles inside the boundary, and Maverick County Canal is 0.7 miles outside it. No mapped street crossing of a named stream is shown inside the community, and no lakes or ponds are mapped within one mile.
Whose permission does a bore in Eidson Road, Maverick County need?
Eidson Road has no city government, so streets fall under county or state authority rather than a city department. For work in the Loop 480 right of way, TxDOT’s Laredo District reviews the utility permit. The utility owner, not the drilling contractor, files through TxDOT’s online RULIS system; we prepare the bore plan and profile for that filing and work under the owner’s permit. Any Union Pacific track crossing needs an agreement with the railroad, and TxDOT requests a copy when the line also occupies highway right of way. A crossing of Maverick County Water Ditch is checked for federal jurisdiction during planning.
Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.
Who owns the lines near Eidson Road in Maverick County?
The water provider for a specific Eidson Road address has to be confirmed with the county or local water district before a bore is planned. EPA drinking water records do not connect a system to this community, and no system carries its name, so the provider cannot be matched from those records. AEP Texas Central and Rio Grande Electric Cooperative report electric service in Maverick County; we confirm the line owner for the route before planning an electric conduit bore.
| Line owner | What it is | Source | Size |
|---|---|---|---|
| AEP Texas Central and Rio Grande Electric Cooperative | Electric utilities reporting service in Maverick County | EIA Form 861 | Confirm the line owner by address |
The American Community Survey 2019 to 2023 five year estimates put the median home year in Eidson Road at 1996: 2 percent were built before 1960, 55 percent from 1960 to 1999, and 43 percent in 2000 or later. That mix can mean either replacement lines or new service extensions along Canal Road. Before drilling near a marked utility, we hydrovac pothole it to verify its depth; paint shows its position, not how deep it sits.

Where is Eidson Road in relation to Eagle Pass?
Eidson Road is an unincorporated community in Maverick County, north of Eagle Pass. It covers 7.04 square miles and sits at an elevation of 743 feet, with ZIP code 78852. Las Quintas Fronterizas is 1.6 miles northeast, and Eagle Pass is 2.8 miles north; Eagle Pass is also the county seat and the nearest larger city. Chula Vista is 3.7 miles east, Rosita is 4.6 miles southeast, and Fabrica is 4.9 miles north. The Yukon yard is 596 road miles away, a drive of 11.9 hours, which affects mobilization for Loop 480 work.
Places near Eidson Road
- Directional boring in Las Quintas Fronterizas: 1.6 miles northeast
- Directional boring in Eagle Pass: 2.8 miles north
- Directional boring in Chula Vista: 3.7 miles east
- Directional boring in Rosita: 4.6 miles southeast
- Directional boring in Fabrica: 4.9 miles north
What kinds of bores come up in Eidson Road near Venesa Street?
- Highway crossing: A Loop 480 bore needs a planned path beneath the highway pavement and enough clearance for the full crossing.
- Street utility: A Canal Road water or sewer route can go below pavement, with marked utilities exposed before the drill approaches them.
- Fiber conduit: A Venesa Street conduit bore can connect a route without cutting the street surface.
- Rail crossing: A Union Pacific track crossing needs railroad agreement and a bore plan suited to the track crossing.
- Drainage crossing: A route near Maverick County Water Ditch needs depth planning for the channel and a jurisdiction check during planning.
- Service extension: A water, sewer or electric service along Eidson Road needs address specific utility identification and a route that fits the existing street corridor.
More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.
What do you need to quote directional boring in Eidson Road?
For a quote on an Eidson Road route, send the address or map pin, what will go in the ground, the pipe or conduit size and the footage; a sketch or plans help. A route near Loop 480, Canal Road or Union Pacific track helps us see which crossings, access points and existing lines shape the work.
The route details drive the price, with ground conditions first because Lagloria soil, clay and mapped weathered bedrock can change drilling and reaming needs. We also account for pipe or conduit size, footage, utilities to expose, pavement or concrete, drainage crossings, pits, excavator time and sand backfill. A Loop 480 or Union Pacific crossing adds its own planning needs. Mobilization matters too: Eidson Road is 596 road miles from the Yukon yard. High profile or emergency work can also change the scope.
Questions people ask about boring in Eidson Road
Does Trinity Boring Solutions take directional boring work in Maverick County’s Eidson Road, and who staffs it?
Yes. Trinity Boring Solutions takes directional boring work in Eidson Road, and the job is handled by our own crews or partner drilling contractors we have vetted. The water provider must be confirmed for the specific address, while AEP Texas Central and Rio Grande Electric Cooperative report electric service in Maverick County.
Who controls Venesa Street in Eidson Road, and can we bore without cutting it?
Eidson Road is unincorporated, so it has no city government; street authority is county or state, depending on the road. A bore under Venesa Street can avoid cutting the pavement, subject to the route and required approvals. We expose marked utilities along the bore path before drilling near them.
How old are Eidson Road’s homes and buried lines near Canal Road, and what does that mean for replacement bores?
The American Community Survey 2019 to 2023 estimates place the median home year in Eidson Road at 1996. That age profile does not establish the age of buried lines, but Canal Road work could involve replacing an older line or adding a new service. We pothole marked utilities before drilling near them.
Does Lagloria soil in Eidson Road corrode steel, and what pipe should a bore use?
The USDA soil survey maps high steel corrosion risk across 84 percent of Eidson Road. The line owner should consider the material and any coating for steel casing or tracer wire; HDPE is not affected by soil corrosion. We use the route specific plan rather than choose a pipe material for the owner.
What ground does a bore pass through in Eidson Road’s Lagloria soil?
Lagloria is mapped across 46 percent of Eidson Road, and very fine sandy loam is mapped at about 40 inches across 46 percent of the area. The survey also maps clay loam, cemented bedrock and clay at that depth. These are mapped soil patterns, not test borings, so a route needs site specific review.
Will a bore in Eidson Road hit rock, and how much bedrock is mapped within five feet?
The USDA soil survey maps bedrock within five feet in 16 percent of Eidson Road, and that mapped bedrock is weathered. Hard bedrock is not mapped within that depth, but conditions can vary along a route. If a Canal Road bore meets weathered rock, drilling may take longer than in soil.
How far is Eidson Road from Eagle Pass and Trinity’s Yukon, Oklahoma main office?
Eidson Road is 596 road miles from the Yukon yard, with a listed drive time of 11.9 hours. Eagle Pass is 2.8 miles north and is the county seat. That distance can affect mobilization for a Loop 480 crossing or a job on one of the community’s named streets.
How much 811 notice does an Eidson Road bore need, and what if the marks move?
For a bore on Eidson Road, submit the Texas811 locate request at least two working days before excavation, not counting Saturdays, Sundays or legal holidays. The request cannot be made more than 14 days before work starts. If the start slips more than 14 days past the original notice, make a new request; refresh worn or moved marks through Texas811 before work continues.
What affects the cost of directional boring in Eidson Road near Loop 480?
The price depends on the job route and scope, not only footage. Lagloria soil and mapped weathered bedrock can affect drilling time; Loop 480 pavement, Union Pacific track crossings and utilities to expose can add work. Pipe size, pits, drainage crossings, equipment time and mobilization from the Yukon yard also shape the quote.
Where the Eidson Road facts on this page come from
- USDA Natural Resources Conservation Service, Soil Data Access: soil survey map units inside Eidson Road
- U.S. Census Bureau, TIGER/Line 2024: Eidson Road boundary, roads, rail lines and streams
- U.S. Census Bureau, 2020 Census: Eidson Road population count
- U.S. Census Bureau, American Community Survey 2019 to 2023: Eidson Road housing units and year built
- Macrostrat geologic map compilation: map units under Eidson Road
- U.S. Department of Transportation, North American Rail Network: track owners in Maverick County
- U.S. Energy Information Administration, Form EIA 861: electric utilities serving Maverick County
- U.S. Geological Survey, Elevation Point Query Service: Eidson Road elevation
- OpenStreetMap road network through the OSRM router: road miles from Yukon, Oklahoma to Eidson Road
- Texas Utilities Code Chapter 251, Underground Facility Damage Prevention and Safety
- TxDOT Utility Accommodation Rules, 43 Tex. Admin. Code 21.40: underground utilities
- Texas Department of Transportation: Right of Way Utility and Leasing Information System (RULIS) utility permits
Get a Quote for a Bore in Eidson Road
Send the address, what is going in, the size and the footage.
Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com
Free Bore Planner
Plan Your Bore in Eidson Road, Texas
Type the address of your job in Eidson Road. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.
Talk to the crew that does the work
Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.
Answered by a person, not a call center.
Would rather not call? Send the details and we will come back with a written quote.
County and State Pages for Eidson Road
Same county: Elm Creek · Siesta Acres · Radar Base · Seco Mines · Quemado · El Indio · Normandy. All counties: Texas county list.
