trinityboringsolutions.com

Seco Mines Texas Directional Boring: Lagloria Soil, US 277 and Elm Creek

Quick Answer: Yes, we can install a line beneath US 277 without cutting its pavement using directional boring, also called horizontal directional drilling (HDD), in Seco Mines, Texas. From Del Rio Boulevard, our Yukon, Oklahoma main office is 589 road miles away, so mobilization is part of planning. Lagloria soil is the leading mapped series, and very fine sandy loam covers 57 percent of the surface. On a Lagloria route, fine material can slump behind the bit, so we support the hole with fluid and staged reaming.

Family Business Since 1965 Boring Since 1982 24 Hour Phone No Utility Strike in 25 Years

Seco Mines bores at a glance

  • Unincorporated community in Maverick County, Texas. Population 572 (2020 Census count).
  • Road distance from our Yukon, Oklahoma main office: 589 miles, about 11.7 hours of driving.
  • Ground: Lagloria soil is mapped on 31 percent of the area, with very fine sandy loam about 40 inches down.
  • Rock: bedrock is mapped within 60 inches on 23 percent of the area.
  • Highways inside the boundary: US 277 and FM 1589. State permit office: TxDOT Laredo District.
  • Railroad track inside the boundary: none mapped.
  • Named streams inside the boundary: Elm Creek and Seco Creek.
  • Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
  • Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
  • Phone answered 24 hours a day: (405) 409-7423

Who can I call for directional boring near US 277 in Seco Mines?

Trinity Boring Solutions takes directional boring work in Seco Mines, Maverick County, including routes beneath US 277 and Del Rio Boulevard. Can we get your line under a road or creek without cutting it? Yes, we can plan a bore under US 277 or Seco Creek. The Census Bureau’s 2020 count is 572, with no yearly estimate for unincorporated Seco Mines; we route water, sewer, gas, electric conduit and fiber along streets such as Ritchie Road where the plan requires.

Our main office is in Yukon, Oklahoma, and Seco Mines work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. We have been boring since 1982, after the family business began in 1965; four decades in the trade matter where Lagloria soil gives way to mapped bedrock, because ground changes can alter steering and reaming.

Trinity Boring Solutions Vermeer D24x40 directional drill set up for a bore
Our Vermeer D24x40 directional drill set up for a bore. Photos on this page are from our jobs in Oklahoma and Texas.

What is Lagloria soil like to bore in Seco Mines?

The USDA soil survey maps Lagloria across 31 percent of Seco Mines, with Rio Grande at 26 percent, Copita at 22 percent and Reynosa at 20 percent. At the surface, very fine sandy loam accounts for 57 percent, while sandy clay loam accounts for 22 percent and silty clay loam for 20 percent. About 40 inches down, very fine sandy loam is mapped across 31 percent and stratified loamy very fine sand to silt loam across 26 percent. These mapped patterns guide planning, not test borings.

USDA soil survey, inside the Seco Mines mapped community boundaryWhat is mapped
Soil series mappedLagloria 31 percent, Rio Grande 26 percent, Copita 22 percent and Reynosa 20 percent
Texture at the surfacevery fine sandy loam 57 percent, sandy clay loam 22 percent and silty clay loam 20 percent
Texture about 40 inches downvery fine sandy loam 31 percent, stratified loamy very fine sand to silt loam 26 percent and cemented bedrock 22 percent
Engineering class about 40 inches downlean clay (CL) 47 percent and silty clay (CL ML) 31 percent
Average clay content about 40 inches down18 percent
Bedrock mapped within 60 inches23 percent of the area (0 percent hard rock, 23 percent weathered rock)
Seasonal water table within 60 inches0 percent of the area
Flood prone soils26 percent of the area
High corrosion risk for uncoated steel100 percent of the area

At about 40 inches, the USDA soil survey maps cemented bedrock under 22 percent of Seco Mines, and bedrock occurs within 60 inches across 23 percent; weathered bedrock is mapped across 23 percent, with no hard bedrock mapped in that depth range. Seasonal water table is not mapped within 60 inches, but flood prone soils cover 26 percent, including areas near Elm Creek and Seco Creek. High steel corrosion risk applies across 100 percent of the mapped area, so the line owner should consider casing and tracer wire materials; HDPE avoids that soil concern. The geologic map shows Cenozoic Alluvium, undivided and Late Cretaceous Olmos Formation, so conditions can change between fine deposits and clay or sandstone.

How do we drill Seco Mines very fine sandy loam routes?

We drill Seco Mines routes through very fine sandy loam by matching fluid and reaming to the texture, then track the drill head to keep the planned line under local streets and crossings.

  1. At Lagloria very fine sandy loam, we control drilling fluid and open the hole in stages so loose fine grains are less likely to cave around the pipe.
  2. Where mapped clay layers occur near Seco Mines streets, we adjust fluid and reaming to limit sticky cuttings and avoid leaving the hole open after it is ready for pipe.
  3. Where cemented bedrock is mapped under 22 percent of the area at about 40 inches, we plan for slower drilling and watch the soil to rock transition.
  4. Near Elm Creek or Seco Creek, we track the drill head from the surface and log depth and pitch while planning to stay beneath the channel.
Walkover locator at the edge of the wetland on a directional bore at the Cimarron site in Logan County, Oklahoma
Walkover locator at the edge of a wetland on a directional bore in Logan County, Oklahoma.

Where might a Seco Mines bore pass under Del Rio Boulevard?

US 277 runs 0.7 mapped roadway miles inside Seco Mines, and FM 1589 adds 0.4 miles; US 277 Business is 0.3 miles beyond the mapped community boundary. Those routes can call for a bored crossing rather than an open cut, especially beneath existing highway pavement. Del Rio Boulevard is the longest named street at 0.69 miles, followed by Ritchie Road at 0.65 miles and Hopedale Road at 0.36 miles. A route along these streets still needs utility marks and exact crossing points before we set the bore path.

CrossingTypeMapped extentWho has a say
US 277US highway0.7 roadway miles insideState highway office
FM 1589State highway0.4 roadway miles insideState highway office
US 277 BusinessHighway nearby0.3 miles outsideState highway office
Union PacificRailroad nearby0.4 miles outsideThe railroad
Elm CreekStream0.91 channel miles insideChecked for Corps of Engineers jurisdiction
Seco CreekStream0.8 channel miles insideChecked for Corps of Engineers jurisdiction
Swipe the table sideways to see every column.

No railroad runs inside the mapped community boundary, but Union Pacific track is 0.4 miles outside it; a proposed route that reaches the track needs the railroad’s crossing agreement. No mapped street and rail crossings are recorded inside Seco Mines. Elm Creek runs 0.91 channel miles and Seco Creek 0.8 miles through the community, with two mapped street crossings of named streams. There are no lakes or ponds mapped within one mile, so creek crossings, not lake routes, are the water feature to assess.

Who approves Seco Mines work in Maverick County?

Seco Mines is an unincorporated census designated place with no city government, so county or state authorities handle streets and permits around Del Rio Boulevard. For work in US 277 or FM 1589 right of way, the line owner, not the driller, applies through TxDOT RULIS; TxDOT Laredo District reviews it, using the bore plan and profile we prepare. At crossings, electric, communication, water and pressurized sewer lines need 60 inches of cover; TxDOT rules set 48 inches for electric and communication along right of way and 36 inches for water. Union Pacific requires an agreement for a track crossing, and Elm Creek work is checked for federal jurisdiction.

Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.

Which utilities may have lines in Seco Mines, Maverick County?

EPA drinking water records do not let us match a public water system to a Seco Mines address, so confirm the provider for the specific address with the county or local water district before planning a bore. AEP Texas Central and Rio Grande Electric Cooperative report service in Maverick County, but the line owner must be confirmed before an electric conduit bore along US 277 or FM 1589. That check can establish which existing service needs protection at the proposed crossing.

Line ownerWhat it isSourceSize
AEP Texas Central and Rio Grande Electric CooperativeElectric utilities reporting service in Maverick CountyEIA Form 861Confirm the line owner by address
Swipe the table sideways to see every column.

American Community Survey 2019 to 2023 five year estimates put Seco Mines housing at a median build year of 1939 or earlier; 63 percent predates 1960 and 37 percent dates to 2000 or later. That mix means a Del Rio Boulevard job could involve either an older line replacement or a newer service, but the age data does not locate a pipe. We hydrovac pothole marked utilities along the planned route before drilling near them, since paint shows position, not depth.

Coiled black HDPE conduit fitted with a pulling grip staged on a lawn along a completed bore path
Coiled HDPE conduit fitted with a pulling grip, staged on a lawn along a finished bore path.

How far is Seco Mines from Eagle Pass and our Yukon office?

Seco Mines sits in Maverick County at 731 feet and covers 0.57 square miles in the mapped community boundary; its ZIP code is 78852. Siesta Acres is 0.7 miles northeast, Fabrica 0.8 miles southeast and Elm Creek 1.9 miles north. Eagle Pass, the nearest larger city and county seat, is 2.8 miles south. From Yukon, Oklahoma, the job is 589 road miles and a drive of 11.7 hours; that distance affects how we plan mobilization for a bore around US 277.

Places near Seco Mines

What boring work comes up near Elm Creek in Seco Mines?

  • Highway crossing: A US 277 bore can pass beneath the roadway without opening pavement, subject to the TxDOT route and permit plan.
  • Street utility: A water or fiber run along Del Rio Boulevard needs a marked path and potholes at conflicts before drilling.
  • Creek crossing: A route beneath Elm Creek must account for mapped flood prone soils and the channel crossing review.
  • Rail crossing: If a Seco Mines route extends to the Union Pacific track 0.4 miles outside the boundary, an agreement sets crossing conditions.
  • Electric conduit: Along FM 1589, we first confirm the line owner because AEP Texas Central and Rio Grande Electric Cooperative report county service.
  • Service replacement: A bore near Ritchie Road can route a new water or sewer connection around surface pavement and marked existing lines.

More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.

What should I send to price a Seco Mines bore near Cenizo Heights?

For a Seco Mines quote, send a map pin for the exact address; a point on Cenizo Heights or near Seco Creek changes which utilities, pavement and drainage crossings fall on the route. Tell us what line is going in, its pipe or conduit size and footage. A sketch or plans help us shape the bore path and flag questions before quoting.

The job scope determines price through ground, crossings and logistics. Lagloria very fine sandy loam may ream differently from areas where cemented bedrock is mapped, so soil and rock affect time. A path under US 277 can add pavement and permit requirements; an Elm Creek crossing adds waterway planning, and nearby utilities must be exposed. Length, pipe size, pits, excavator time, sand backfill and concrete also matter. At 589 road miles from Yukon, mobilization is part of the estimate.

Questions people ask about boring in Seco Mines

Does Trinity take directional boring jobs in Seco Mines, Maverick County?

Yes. We take Seco Mines work and keep Trinity as your contact from the first call through the bore log, whether our own crew or a vetted partner contractor is on site. For a route under US 277 or along Del Rio Boulevard, our staffing plan follows the job location and scope.

What ground should I expect in Seco Mines around Lagloria soil?

The USDA soil survey maps Lagloria across 31 percent of Seco Mines, and very fine sandy loam is the most common surface texture at 57 percent. At about 40 inches, very fine sandy loam remains mapped across 31 percent, while cemented bedrock is mapped under 22 percent. Those layers can change how the hole holds.

Is there rock near the surface on a Seco Mines bore?

Bedrock is mapped within 60 inches across 23 percent of Seco Mines, and the survey maps weathered bedrock across that same share; hard bedrock is not mapped within 60 inches. That does not rule out rock below the mapped depth, so a route near the Olmos Formation still needs planning against actual conditions.

Who approves a bore under US 277 in Seco Mines?

The utility owner files for a TxDOT right of way permit through RULIS; the driller does not file it. TxDOT Laredo District reviews a US 277 application, and we prepare the bore plan and profile for the owner’s filing. Permit conditions set cover, so route and line type matter.

What does a Seco Mines bore under Union Pacific track require?

Union Pacific owns the track mapped 0.4 miles outside the Seco Mines boundary, not inside it. A bore that crosses that track needs the railroad’s crossing agreement, which establishes the required crossing conditions. If the route also occupies US 277 right of way, TxDOT asks for a copy of that agreement.

Can a line be bored under Elm Creek in Seco Mines?

A line can be planned beneath Elm Creek, which has 0.91 channel miles inside Seco Mines, but the crossing needs a route specific review. Flood prone soils cover 26 percent of the community, and creek work is checked for U.S. Army Corps of Engineers jurisdiction during planning. The bore path and depth must be set to stay beneath the channel.

How much notice does Texas811 need for a Seco Mines bore along Del Rio Boulevard?

Texas811 needs a locate request at least 48 hours before excavation for a bore along Del Rio Boulevard, excluding Saturdays, Sundays and legal holidays; submit it no more than 14 days ahead. A start more than 14 days after the original notice calls for a fresh request. Marks that fade or move must be refreshed through Texas811 before work resumes.

How far is Seco Mines from the Yukon office near Eagle Pass?

Seco Mines is 589 road miles from Trinity’s Yukon, Oklahoma main office, with a drive of 11.7 hours. Eagle Pass lies 2.8 miles south and is the nearest larger city, but the distance from Yukon still affects crew mobilization for a Del Rio Boulevard bore. We coordinate the job through Trinity regardless of which crew is on site.

What affects the cost of a Seco Mines directional bore under US 277?

Cost for a Seco Mines bore under US 277 depends on footage, pipe or conduit size, mapped ground, pavement and the number of utilities to cross and expose. Lagloria soil, possible cemented bedrock and an Elm Creek crossing can change the drilling plan; pits, sand backfill, excavator time and mobilization from Yukon also affect the job. A map pin makes those route conditions clearer.

Where the Seco Mines facts on this page come from

Darren Rice in a safety vest at the bore pit beside the Trinity Boring Solutions Ditch Witch directional drill, with drill rods racked, on the airfield at Will Rogers World Airport in Oklahoma City

About Trinity Boring Solutions

Trinity Boring Solutions is a family business in Yukon, Oklahoma, founded by Dean Rice in 1965 and owned today by Darren Rice, who started its directional boring side in 1982. The company bores across Oklahoma and Texas. No bore is too big or too small: 4 foot sidewalk sleeves to roughly 4,100 feet under the Arkansas River in Tulsa. Reach us at (405) 409-7423.

Get a Quote for a Bore in Seco Mines

Send the address, what is going in, the size and the footage.

Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com

Trinity Boring Solutions | 24/7 Available ☎ Call (405) 409-7423 Free Quote

Free Bore Planner

Plan Your Bore in Seco Mines, Texas

Type the address of your job in Seco Mines. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.

Talk to the crew that does the work

Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.

Call (405) 409-7423

Answered by a person, not a call center.

Would rather not call? Send the details and we will come back with a written quote.

Quick Quote In Page

County and State Pages for Seco Mines

Same county: Eidson Road · Chula Vista · Rosita · Radar Base · Quemado · El Indio · Normandy. All counties: Texas county list.