trinityboringsolutions.com

Emerald Bay Texas Directional Boring: Bernaldo Soil, FM 344 and Saline Creek

Quick Answer: Emerald Bay is an unincorporated community in Smith County, so Bay Drive is not a city owned street. We provide directional boring, also called horizontal directional drilling (HDD), for work beneath FM 344 and local streets. The Yukon main office is 325 road miles from Emerald Bay, so mobilization is part of planning for Bay Drive work. At 40 inches, sandy clay loam is mapped under 49 percent of the area, a ground detail we use to plan the bore.

Family Business Since 1965 Boring Since 1982 24 Hour Phone No Utility Strike in 25 Years

Emerald Bay bores at a glance

  • Unincorporated community in Smith County, Texas. Population 1,146 (2020 Census count).
  • Road distance from our Yukon, Oklahoma main office: 325 miles, about 6.3 hours of driving.
  • Ground: Bernaldo soil is mapped on 19 percent of the area, with sandy clay loam about 40 inches down.
  • Rock: no bedrock is mapped in the top 60 inches.
  • Highways inside the boundary: FM 344. State permit office: TxDOT Tyler District.
  • Railroad track inside the boundary: none mapped.
  • Public water: Emerald Bay Municipal Utility District, groundwater wells.
  • Texas811: locate request at least two working days before a bore and no more than 14 days ahead.
  • Range: 3/4 inch service lines to 48 inch casing, 10 feet to 5,000 feet.
  • Phone answered 24 hours a day: (405) 409-7423

Which contractor handles directional boring near FM 344 in Emerald Bay?

Emerald Bay is an unincorporated community in Smith County, and Trinity Boring Solutions takes directional boring work there, including routes along streets such as Bay Drive that have no city government owner. The Census Bureau counted 1,146 people in 2020; it does not publish yearly estimates for unincorporated places. We install water, sewer, gas, electric conduit and fiber lines along local streets or beneath FM 344 when the route calls for it.

Our main office is in Yukon, Oklahoma, and Emerald Bay work is done with our own crews and from satellite yards run by partner drilling contractors Trinity has personally vetted. Our longest bore runs roughly 4,100 feet with 48 inch pipe under the Arkansas River in Tulsa. A service line near Bay Drive is a smaller scope to assess against that reach. We are a family business started in 1965, with directional boring work dating to 1982.

Trinity Boring Solutions Vermeer D24x40 directional drill set up for a bore
Our Vermeer D24x40 directional drill set up for a bore. Photos on this page are from our jobs in Oklahoma and Texas.

What kind of ground should a bore expect in Emerald Bay near Bernaldo soil?

The USDA soil survey maps Bernaldo fine sandy loam on 19 percent of Emerald Bay, Cuthbert fine sandy loam on 12 percent and Oakwood fine sandy loam on 10 percent. Fine sandy loam is the mapped surface texture across 48 percent of the area. At about 40 inches below the surface, sandy clay loam is mapped under 49 percent, and the average clay content there is 25 percent. Those are soil map patterns, not test borings; a route near Bay Drive still needs site specific planning.

USDA soil survey, inside the Emerald Bay mapped community boundaryWhat is mapped
Soil series mappedBernaldo 19 percent, Cuthbert 12 percent, Oakwood 10 percent and Gallime 7 percent
Texture at the surfacefine sandy loam 48 percent
Texture about 40 inches downsandy clay loam 49 percent
Engineering class about 40 inches downlean clay (CL) 31 percent and clayey sand (SC) 20 percent
Average clay content about 40 inches down25 percent
Bedrock mapped within 60 inchesNone mapped
Seasonal water table within 60 inches39 percent of the area
Flood prone soils0 percent of the area
High corrosion risk for uncoated steel19 percent of the area

Bedrock is not mapped in the top five feet of Emerald Bay, so the soil survey does not point to shallow rock on a Bernaldo route. A seasonal water table is mapped within 60 inches under 39 percent of the area, which can mean wet pits that need pumping. We consider the Bernaldo, Cuthbert, Oakwood and Gallime soil series in boring plans; flood prone soils are not mapped. High steel corrosion risk covers 19 percent, so the line owner should consider casing and tracer wire protection. The mapped geologic unit is Water, covering 49 percent; no age is given.

What does it take to bore Emerald Bay’s sandy clay loam?

The USDA soil survey maps sandy clay loam at about 40 inches under 49 percent of Emerald Bay, so we plan the drilling fluid and reaming around the actual route rather than treating Bay Drive as uniform ground.

  1. We review the route against the Bernaldo and Cuthbert soil map units, then choose fluid and reaming steps for the ground expected along the proposed alignment.
  2. A seasonal water table is mapped within 60 inches under 39 percent of Emerald Bay, so we plan practical pit locations and pumping where wet ground is encountered.
  3. Before the drill approaches a marked line near the Emerald Bay Municipal Utility District system or electric conduit, we expose it with hydrovac potholing.
  4. We track the drill head from the surface and log depth and pitch, keeping a bore beneath Bay Drive from cutting the street pavement.
Open bore pit in red Oklahoma dirt with white PVC conduit stub ups and an orange safety barrier
An open bore pit in red Oklahoma dirt with PVC conduit stubbed up and a safety barrier around it.

Where does a line have to go under Bay Drive in Emerald Bay?

FM 344 is the state highway mapped inside Emerald Bay, with 0.9 roadway miles in the community; Texas State Highway 155 is 0.3 miles outside the mapped boundary. A line beneath FM 344 needs a bore plan suited to the highway right of way. Bay Drive is the longest named street at 3.07 miles, followed by La Salle Road at 0.72 miles and Fairway Drive at 0.58 miles. Lakeside Drive adds another named route to check against the proposed alignment.

CrossingTypeMapped extentWho has a say
FM 344State highway0.9 roadway miles insideState highway office
Texas State Highway 155Highway nearby0.3 miles outsideState highway office
Saline CreekStream nearby0.5 miles outsideChecked for Corps of Engineers jurisdiction
Rose BranchStream nearby0.6 miles outsideChecked for Corps of Engineers jurisdiction
County Line CreekStream nearby0.9 miles outsideChecked for Corps of Engineers jurisdiction
Swipe the table sideways to see every column.

No railroad is mapped inside Emerald Bay or within 1 mile outside it, so there is no mapped track crossing to plan for. Saline Creek, Rose Branch and County Line Creek are within 1 mile of the community boundary, but no named stream is mapped inside it. We account for Saline Creek when planning nearby boring because no lakes or ponds are mapped within 1 mile of Emerald Bay. Unnamed drainage totals 4.18 miles inside the community, so the route still needs a drainage check even where no named creek crossing is mapped.

Who has to sign off on a bore in Emerald Bay and Smith County?

Emerald Bay has no city government, so a local city permit office does not control Bay Drive or the other community streets; check the applicable county authority for work on county roads. FM 344 is a state highway, and work in its right of way needs a TxDOT utility permit reviewed by the TxDOT Tyler District. The utility that owns the line files through TxDOT’s RULIS system, while we provide the bore plan and profile. Texas State Highway 155 is nearby, so its right of way status matters if the route reaches it. No railroad crossing is mapped. A crossing near Saline Creek should be checked for federal water jurisdiction during planning.

Read the rules for yourself: Texas Utilities Code Chapter 251 on notice to Texas811, the Texas811 questions and answers page, the TxDOT Utility Accommodation Rules, 43 TAC 21.40 and TxDOT utility permits in RULIS.

Which utilities should a bore near Emerald Bay Municipal Utility District account for?

Emerald Bay Municipal Utility District serves 1,875 people through 625 service connections, with groundwater wells as its source. A planned water service near Bay Drive should be coordinated with the district before drilling. Electric service reported in Smith County includes Oncor Electric Delivery Company, Southwestern Electric Power, Cherokee County Electric Cooperative Association, Upshur Rural Electric Cooperative and Wood County Electric Cooperative. We confirm the line owner at the bore location before setting conduit specifications; the county list does not identify one provider for every address.

Line ownerWhat it isSourceSize
Emerald Bay Municipal Utility DistrictPublic water systemGroundwater wells625 connections, 1,875 people served
Oncor Electric Delivery Company, Southwestern Electric Power, Cherokee County Electric Cooperative Association, Upshur Rural Electric Cooperative and Wood County Electric CooperativeElectric utilities reporting service in Smith CountyEIA Form 861Confirm the line owner by address
Swipe the table sideways to see every column.

The American Community Survey 2019 to 2023 estimates give Emerald Bay a median housing year of 1985; 79 percent of units date from 1960 to 1999, and 21 percent were built in 2000 or later. A replacement bore along La Salle Road may need to work around older buried lines, while a newer service has its own route and connection points. Before drilling near the district water lines or electric conduit, we hydrovac pothole each marked utility to confirm its depth and position.

Hydrovac truck and boring equipment staged beside an airport taxiway for utility daylighting in Oklahoma City
Our hydrovac truck and boring equipment beside an airport taxiway in Oklahoma City, set up to expose a utility crossing.

Do you cover Emerald Bay and nearby Shadybrook?

Emerald Bay is in Smith County on the eastern side of Lake Palestine, and we take directional boring work there and around nearby Shadybrook. The community covers 0.77 square miles at an elevation of 365 feet, with ZIP code 75757. Coffee City is 3.0 miles southwest, Shadybrook is 3.1 miles south, Sunrise Shores is 4.2 miles west, Berryville is 5.3 miles south and Noonday is 6.1 miles northeast. Bullard is the nearest larger city, 7.2 miles east; Tyler, the county seat, is 13.3 miles northeast. The Yukon main office is 325 road miles away, a 6.3 hour drive.

Places near Emerald Bay

What boring work comes up near Saline Creek in Emerald Bay?

  • Highway crossing: A bore beneath FM 344 follows the TxDOT plan and profile, with cover set by the utility type and permit.
  • Water service: A connection near Bay Drive needs coordination with Emerald Bay Municipal Utility District and potholing around its existing groundwater lines.
  • Fiber route: A fiber bore along La Salle Road uses a planned alignment that accounts for marked utilities and the street surface.
  • Creek approach: A route near Saline Creek needs drainage and water jurisdiction review before pits and bore depth are set.
  • Conduit crossing: Electric conduit near Fairway Drive requires confirming the line owner and exposing marked utilities before drilling.
  • Drainage route: Unnamed drainage within Emerald Bay calls for checking the path and pit locations before a bore is laid out.

More on each kind of work: water line boring, electric line boring, fiber optic boring, road, railroad and creek crossings and municipal boring.

What drives the price of a bore near Lakeside Drive in Emerald Bay?

A map pin is the best starting point because a proposed route near Lakeside Drive may differ from one approaching Bay Drive or the FM 344 right of way. For FM 344 work, we need the address or pin, what will go underground, the pipe or conduit size, and footage. A sketch or plans help us see nearby lines, pavement and drainage before we set the scope.

On Bay Drive, we price the full job scope rather than judging cost by footage alone. Bernaldo soil and the sandy clay loam mapped at depth affect drilling choices; utilities to expose, concrete or pavement, pits and sand backfill add work. A crossing under FM 344 brings permit planning into the scope, while a creek or drainage route needs its own review. Mobilization also matters because Emerald Bay is 325 road miles from the Yukon main office. Emergency timing or excavator time can change the work plan.

Questions people ask about boring in Emerald Bay

Does Trinity Boring Solutions take directional boring jobs in Emerald Bay, Smith County?

Yes. We take directional boring work in Emerald Bay, an unincorporated community in Smith County. Work is handled by our own crews or from satellite yards run by partner drilling contractors we have vetted. The customer works with Trinity from the initial call through the bore log, including on a route along Bay Drive.

Who supplies water in Emerald Bay, and is it groundwater?

Emerald Bay Municipal Utility District operates the public water system, which draws from groundwater wells. Public records list 625 service connections and 1,875 people served; we use that context when planning underground work in Emerald Bay. A proposed service near Bay Drive should be checked with the district, and marked water lines should be exposed before the drill approaches.

Which electric company serves Emerald Bay, Smith County, and who confirms conduit specs?

The county reports service from Oncor Electric Delivery Company, Southwestern Electric Power, Cherokee County Electric Cooperative Association, Upshur Rural Electric Cooperative and Wood County Electric Cooperative. That list does not establish which one serves a particular address near Fairway Drive. We confirm the line owner before conduit specifications are set.

Does the county or a city control Fairway Drive in Emerald Bay, and must it be cut?

Emerald Bay is unincorporated and has no city government, so Fairway Drive is not a city owned street. Confirm the road authority for the specific location. Directional boring can place a line beneath the pavement using pits beside the route, avoiding an open cut through Fairway Drive when the planned bore is suitable.

Could older buried lines affect a replacement bore on La Salle Road in Emerald Bay?

They could. The American Community Survey 2019 to 2023 estimates place the median housing year at 1985, with 79 percent of units built from 1960 to 1999. A replacement line near La Salle Road may meet existing utilities, so we expose marked lines by hydrovac before drilling near them.

Are groundwater or flood prone soils a concern for bore pits near Saline Creek in Emerald Bay?

Seasonal groundwater can affect pits: it is mapped within 60 inches under 39 percent of Emerald Bay. Flood prone soils are not mapped, but Saline Creek is 0.5 miles from the community boundary, so a nearby route still needs a drainage and water jurisdiction check. Wet pits may require pumping.

How far is Emerald Bay from the Yukon office, and does Bullard affect mobilization?

Emerald Bay is 325 road miles and a 6.3 hour drive from the Yukon main office. Bullard is 7.2 miles east and is the nearest larger city, but mobilization is planned from the Yukon office. The distance is one job factor for work along FM 344 or Bay Drive.

How early should I call Texas811 for a bore on Bay Drive in Emerald Bay?

For a bore on Bay Drive, submit the Texas811 locate request at least 48 hours before excavation, excluding Saturdays, Sundays and legal holidays, and no earlier than 14 days before work. For a Texas State Highway 155 crossing, if the start moves more than 14 days past the original notice, we submit a new request. Have worn or moved marks refreshed through Texas811 before work resumes.

What determines the cost of directional boring near FM 344 in Emerald Bay?

The price depends on footage, pipe or conduit size, soil, utilities to expose, pavement, drainage crossings, pits, excavator time and mobilization. Near FM 344, highway right of way planning can add steps; sandy clay loam and a route toward Saline Creek also affect the work plan. We need the exact location and scope to assess the job.

Where the Emerald Bay facts on this page come from

Darren Rice in a safety vest at the bore pit beside the Trinity Boring Solutions Ditch Witch directional drill, with drill rods racked, on the airfield at Will Rogers World Airport in Oklahoma City

About Trinity Boring Solutions

Trinity Boring Solutions is a family business in Yukon, Oklahoma, founded by Dean Rice in 1965 and owned today by Darren Rice, who started its directional boring side in 1982. The company bores across Oklahoma and Texas. No bore is too big or too small: 4 foot sidewalk sleeves to roughly 4,100 feet under the Arkansas River in Tulsa. Reach us at (405) 409-7423.

Get a Quote for a Bore in Emerald Bay

Send the address, what is going in, the size and the footage.

Trinity Boring Solutions
9102 NW Expressway, Yukon, OK 73099
(405) 409-7423 | darren@trinityboringsolutions.com

Trinity Boring Solutions | 24/7 Available ☎ Call (405) 409-7423 Free Quote

Free Bore Planner

Plan Your Bore in Emerald Bay, Texas

Type the address of your job in Emerald Bay. The Bore Planner opens an aerial map at that spot. Drop one pin where the bore starts and one where it ends, tell us what is going in and send the scope to our crew.

Talk to the crew that does the work

Fastest way to a number is a phone call. Tell us where the crossing is and what is going in the ground, and you will get a straight answer on the same call. Bores from 10 feet to 5,000 feet, 3/4 inch service line through 48 inch casing, anywhere in Oklahoma and Texas. We run 24/7 for main breaks and emergency repairs.

Call (405) 409-7423

Answered by a person, not a call center.

Would rather not call? Send the details and we will come back with a written quote.

Quick Quote In Page

County and State Pages for Emerald Bay

Same county: Tyler · Whitehouse · Lindale · Hideaway · Troup · Arp · Winona · New Chapel Hill · Overton. All counties: Texas county list.